And here's the base64 decoded version:

On 15/05/14 22:59, Gradelain Ngouni wrote:
> Hey John,
> 
> here an update of what I’m actually facing:
> this the configuration of my  SVI:
> interesting will be the lines after this:
> 
> ##Primary:
> 
> interface vlan.0.22
> 
>   ip address 10.40.22.253 255.255.255.0 primary
> 
>   vrrp create 22 v2-IPv4
> 
>   vrrp address 22 10.40.22.254
> 
>   vrrp priority 22 200
> 
>   vrrp advertise-interval 22 seconds 5
> 
>   vrrp accept-mode 22
> 
>   vrrp fabric-route-mode 22
> 
>   vrrp enable 22
> 
>   ip helper-address 10.10.20.21
> 
>   ip helper-address 10.10.20.30
> 
>   ip helper-address 10.40.20.99
> 
>   ip helper-address 10.40.20.100
> 
>   no ip proxy-arp
> 
>   no ip redirects
> 
>   ipv6 forwarding
> 
>   no shutdown
> 
> 
> 
> ##secondary:
> 
> interface vlan.0.22
> 
>   ip address 10.40.22.252 255.255.255.0 primary
> 
>   vrrp create 22 v2-IPv4
> 
>   vrrp address 22 10.40.22.254
> 
>   vrrp priority 22 150
> 
>   vrrp advertise-interval 22 seconds 5
> 
>   vrrp accept-mode 22
> 
>   vrrp fabric-route-mode 22
> 
>   vrrp enable 22
> 
>   ip helper-address 10.10.20.21
> 
>   ip helper-address 10.10.20.30
> 
>   ip helper-address 10.40.20.99
> 
>   ip helper-address 10.40.20.100
> 
>   no ip proxy-arp
> 
>   no ip redirects
> 
>   ipv6 forwarding
> 
>   no shutdown
> 
>   exit
> 
> 
> On the S3 Interface vlan.0.22, I ONCE AGAIN  apply “shut” and “no shut”
> With this commands set, the client were able to reach their Gateway and 
> beyond.
> 
> Her’s were it gets once again complicated:
> 
> Client_1 with IP 10.40.22.10   is connected on port ge.1.25 on the S3. NAC 
> only apply the policy  to the user and the VLAN  22 is manually configured on 
> the  user switch port.
> Client 2 with IP 10.40.22.11   is connected on port ge.1.11 on the C5G. NAC 
> Apply the Policy and Dynamically the vlan to the user switch port.
> 
> 
> 1)      Shutdown the port  of Client_1 and enable it again ==> the client is 
> once again reachable
> 
> 2)      Shutdown the port of Client_1 and enable it again ==> client no more 
> reachable!
> 
> a.       Shot down the interface vlan.0.22 and enable it again, then clients 
> once again reachable.
> 
> I’m reporting to GTAC….
> The behavior is a wee bit strange.
> 
> Cheers
> 
> Gradelain


-- 
James Andrewartha
Network & Projects Engineer
Christ Church Grammar School
Claremont, Western Australia
Ph. (08) 9442 1757
Mob. 0424 160 877

---
To unsubscribe from enterasys, send email to [email protected] with the body: 
unsubscribe enterasys [email protected]

Reply via email to