Has anyone implemented the Beckhoff EL6001 RS232 and EL6021 Modbus interfaces
with the etherlab 1.5.2 master? I am having some trouble with both of the
devices and I think the same issue is happening with both modules.
I am able to initialize each of the devices using the ctrl and status register
bits doing the initialization sequence. Also, I can set 4073, 4074, 4075 SDO
registers for configuration on the port with setting the baud rate, data frame,
etc..
Where I am failing is to actually send out the data. Using the structure output
from the ethercat tool in the ethercat 1.5.2 / tool folder, I get the following
for PDO outputs:
// EL6021 PDO entries
ec_pdo_entry_info_t EL60XX_pdo_entries[] = {
{0x3003, 0x01, 16}, /* Ctrl */
{0x3003, 0x02, 8}, /* Data Out 0 */
{0x3003, 0x03, 8}, /* Data Out 1 */
{0x3003, 0x04, 8}, /* Data Out 2 */
{0x3003, 0x05, 8}, /* Data Out 3 */
{0x3003, 0x06, 8}, /* Data Out 4 */
{0x3003, 0x07, 8}, /* Data Out 5 */
{0x3003, 0x08, 8}, /* Data Out 6 */
{0x3003, 0x09, 8}, /* Data Out 7 */
{0x3003, 0x0a, 8}, /* Data Out 8 */
{0x3003, 0x0b, 8}, /* Data Out 9 */
{0x3003, 0x0c, 8}, /* Data Out 10 */
{0x3003, 0x0d, 8}, /* Data Out 11 */
{0x3003, 0x0e, 8}, /* Data Out 12 */
{0x3003, 0x0f, 8}, /* Data Out 13 */
{0x3003, 0x10, 8}, /* Data Out 14 */
{0x3003, 0x11, 8}, /* Data Out 15 */
{0x3003, 0x12, 8}, /* Data Out 16 */
{0x3003, 0x13, 8}, /* Data Out 17 */
{0x3003, 0x14, 8}, /* Data Out 18 */
{0x3003, 0x15, 8}, /* Data Out 19 */
{0x3003, 0x16, 8}, /* Data Out 20 */
{0x3003, 0x17, 8}, /* Data Out 21 */
{0x3103, 0x01, 16}, /* Status */
{0x3103, 0x02, 8}, /* Data In 0 */
{0x3103, 0x03, 8}, /* Data In 1 */
{0x3103, 0x04, 8}, /* Data In 2 */
{0x3103, 0x05, 8}, /* Data In 3 */
{0x3103, 0x06, 8}, /* Data In 4 */
{0x3103, 0x07, 8}, /* Data In 5 */
{0x3103, 0x08, 8}, /* Data In 6 */
{0x3103, 0x09, 8}, /* Data In 7 */
{0x3103, 0x0a, 8}, /* Data In 8 */
{0x3103, 0x0b, 8}, /* Data In 9 */
{0x3103, 0x0c, 8}, /* Data In 10 */
{0x3103, 0x0d, 8}, /* Data In 11 */
{0x3103, 0x0e, 8}, /* Data In 12 */
{0x3103, 0x0f, 8}, /* Data In 13 */
{0x3103, 0x10, 8}, /* Data In 14 */
{0x3103, 0x11, 8}, /* Data In 15 */
{0x3103, 0x12, 8}, /* Data In 16 */
{0x3103, 0x13, 8}, /* Data In 17 */
{0x3103, 0x14, 8}, /* Data In 18 */
{0x3103, 0x15, 8}, /* Data In 19 */
{0x3103, 0x16, 8}, /* Data In 20 */
{0x3103, 0x17, 8}, /* Data In 21 */
};
// EL6021 PDO information
ec_pdo_info_t EL60XX_pdos[] = {
{0x1602, 23, EL60XX_pdo_entries + 0}, /* RxPDO-Map Outputs */
{0x1a02, 23, EL60XX_pdo_entries + 23}, /* TxPDO-Map Inputs */
};
// EL6021 syncs
ec_sync_info_t EL60XX_syncs[] = {
{0, EC_DIR_OUTPUT, 0, NULL, EC_WD_DISABLE},
{1, EC_DIR_INPUT, 0, NULL, EC_WD_DISABLE},
{2, EC_DIR_OUTPUT, 1, EL60XX_pdos + 0, EC_WD_DISABLE},
{3, EC_DIR_INPUT, 1, EL60XX_pdos + 1, EC_WD_DISABLE},
{0xff}
};
I am using these as my defaults since I want to use the full 22 bytes (I know
you can configure between 3, 5, and 22 bytes, in which I would like to stick
with 22).
When I fill the data bytes and set the ctrl bit to transmit data, I get a
transmit success status on the status byte in the next process data exchange
but no data goes out the port. I have the other side of the RS232 interface
hooked up to procomm to verify there is no data coming out of the port. Plus
the activity light does not blink.
Has anyone else had any issues with this?
Thank you!
_______________________________________________
etherlab-users mailing list
[email protected]
http://lists.etherlab.org/mailman/listinfo/etherlab-users
