Thanks for the information. It turns out that I needed to tell tuner that it is type=2.
On Monday 30 December 2002 12:53 pm, you wrote: > On Monday 30 December 2002 12:00 pm, Kent Loobey wrote: > Kent, > It sounds like your using PAL instead of NTSC, or that youve loaded the > module improperly... I had a simular issue and it was becuase I was using > PAL. There is an frequency offset option in your xawtv, I have an offset of > +6 (this makes the channels tune in better... heres what I have... > > fine = +6 > > > Heres what dmesg shows about my tuner... > > Linux video capture interface: v1.00 > i2c-core.o: i2c core module > i2c-algo-bit.o: i2c bit algorithm module > i2c-core.o: driver i2c TV tuner driver registered. > bttv: driver version 0.7.91 loaded > bttv: using 2 buffers with 2080k (4160k total) for capture > bttv: Host bridge is Silicon Integrated Systems [SiS] 620 Host > bttv: Bt8xx card found (0). > PCI: Found IRQ 3 for device 00:09.0 > PCI: Sharing IRQ 3 with 00:09.1 > bttv0: Bt878 (rev 2) at 00:09.0, irq: 3, latency: 64, memory: 0xe7dfe000 > bttv0: detected: (Askey Magic/others) TView99 CPH06x [card=38], PCI > subsystem ID is 144f:3000 > bttv0: using: BT878(TView99 CPH06X) [card=38,insmod option] > tuner: probing bt848 #0 i2c adapter [id=0x10005] > tuner: chip found @ 0xc0 > bttv0: i2c attach [client=Temic NTSC (4036 FY5),ok] > i2c-core.o: client [Temic NTSC (4036 FY5)] registered to adapter [bt848 > #0](pos. 0). > i2c-core.o: adapter bt848 #0 registered as adapter 0. > bttv0: i2c: checking for MSP34xx @ 0x80... not found > bttv0: i2c: checking for TDA9875 @ 0xb0... not found > bttv0: i2c: checking for TDA7432 @ 0x8a... not found > tvaudio: TV audio decoder + audio/video mux driver > tvaudio: known chips: > tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c5 >4 (PV951) > i2c-core.o: driver generic i2c audio driver registered. > bttv0: registered device video0 > bttv0: registered device vbi0 > bttv0: PLL: 28636363 => 35468950 ... ok > bttv0: PLL: switching off > > and heres my .xawtv: > > bubba@bubba:~$ cat .xawtv > [global] > ratio = 4:3 > freqtab = us-cable > pixsize = 128 x 96 > pixcols = 1 > jpeg-quality = 75 > keypad-ntsc = no > keypad-partial = yes > osd = yes > #channel = 3 > # [Station name] > # capture = overlay | grabdisplay | on | off > # input = Television | Composite1 | S-Video | ... > # norm = PAL | NTSC | SECAM | ... > # channel = # > # fine = # (-128..+127) > # key = keysym | modifier+keysym > # color = # > # bright = # > # hue = # > # contrast = # > > [defaults] > norm = NTSC > input = Television > capture = grab > color = 47% > bright = 63% > hue = 47% > contrast = 42% > audio = stereo > fine = +6 > channel = 3 > > #[global] > #freqtab = us-cable > > #[defaults] > #input = Television > #norm = NTSC > [VCR] > channel = 3 > bubba@bubba:~$ > > As you can see from the defaults, my tuner is tuned to chanel 3 because I > use it with my vcr, its easier for me to use the vcr remote... but Ive used > it w/out the vcr, but it needs a really good signal to tune in anything... > which is one reason I use the VCR... it works really good with cable... but > hooking up an antenna to the tv tuner is a lesson in frustration... > > If you send more details (such as the tv tuner card info... what brand, > model, ... I maybe able to find a better config for you. > > Jamie > > : On Monday 30 December 2002 11:35 am, you wrote: > : > Does anyone know how to configure either MoTV or XawTV? > : > > : > I can't fined anyway to tell it what the local broadcast stations are > : > around here. > : > : Maybe I should be more specific. It seems to find the channels but the > : numbers are off by one, e.g., 10 instead of 9, 29 instead of 28, etc. > : > : > Thanks. > : > > : > Kent > : > _______________________________________________ > : > Eug-LUG mailing list > : > [EMAIL PROTECTED] > : > http://mailman.efn.org/cgi-bin/listinfo/eug-lug > : > : _______________________________________________ > : Eug-LUG mailing list > : [EMAIL PROTECTED] > : http://mailman.efn.org/cgi-bin/listinfo/eug-lug _______________________________________________ Eug-LUG mailing list [EMAIL PROTECTED] http://mailman.efn.org/cgi-bin/listinfo/eug-lug
