----- Original Message ----- From: "Davide Minardi" <[EMAIL PROTECTED]> To: "Exim Mailing List" <[email protected]> Sent: Wednesday, August 30, 2006 10:31 AM Subject: Re: [exim] R: Exim4 And outgoing Filters
> > > This is router section of conf file > > > ### router/200_exim4-config_primary > ################################# > # This file holds the primary router, responsible for nonlocal mails > > .ifdef DCconfig_internet > # configtype=internet > # > # deliver mail to the recipient if recipient domain is a domain we > # relay for. We do not ignore any target hosts here since delivering to > # a site local or even a link local address might be wanted here, and if > # such an address has found its way into the MX record of such a domain, > # the local admin is probably in a place where that broken MX record > # could be fixed. > > dnslookup_relay_to_domains: > debug_print = "R: dnslookup_relay_to_domains for [EMAIL PROTECTED]" > driver = dnslookup > domains = ! +local_domains : +relay_to_domains > transport = remote_smtp > same_domain_copy_routing = yes > no_more > > # deliver mail directly to the recipient. This router is only reached > # for domains that we do not relay for. Since we most probably can't > # have broken MX records pointing to site local or link local IP > # addresses fixed, we ignore target hosts pointing to these addresses. > > dnslookup: > debug_print = "R: dnslookup for [EMAIL PROTECTED]" > driver = dnslookup > domains = ! +local_domains > transport = remote_smtp > same_domain_copy_routing = yes > # ignore private rfc1918 and APIPA addresses > ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\ > 172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16 > no_more > > .endif > > > .ifdef DCconfig_local > # configtype=local > # > # Stand-alone system, so generate an error for mail to a non-local domain > nonlocal: > debug_print = "R: nonlocal for [EMAIL PROTECTED]" > driver = redirect > domains = ! +local_domains > allow_fail > data = :fail: Mailing to remote domains not supported > no_more > > .endif > > > .ifdef DCconfig_smarthost DCconfig_satellite > # configtype=smarthost or configtype=satellite > # > # Send all non-local mail to a single other machine (smarthost). > # > # This means _ALL_ non-local mail goes to the smarthost. This will most > # probably not do what you want for domains that are listed in > # relay_domains. The most typical use for relay_domains is to control > # relaying for incoming e-mail on secondary MX hosts. In that case, > # it doesn't make sense to send the mail to the smarthost since the > # smarthost will probably send the message right back here, causing a > # loop. > # > # If you want to use a smarthost while being secondary MX for some > # domains, you'll need to copy the dnslookup_relay_to_domains router > # here so that mail to relay_domains is handled separately. > > smarthost: > debug_print = "R: smarthost for [EMAIL PROTECTED]" > driver = manualroute > domains = ! +local_domains > transport = remote_smtp_smarthost > route_list = * DCsmarthost byname > host_find_failed = defer > same_domain_copy_routing = yes > no_more > > .endif > > > dnslookup: > driver = dnslookup > domains = ! +local_domains > transport = remote_smtp > ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 > > sentarchiver: > driver = dnslookup > domains = ! +local_domains > transport = sent_archive_delivery > ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 > > sent_archive_delivery: > driver = appendfile > user = raziel > group = raziel > delivery_date_add > envelope_to_add > return_path_add > maildir_format=true > mode = 0770 > directory = /home/raziel/Maildir/.Sent > create_directory = true > directory_mode = 0770 > no_mode_fail_narrower > > > > > # The "no_more" above means that all later routers are for > # domains in the local_domains list, i.e. just like Exim 3 directors. > ##################################################### > ### end router/200_exim4-config_primary > ##################################################### > ----- Original Message ----- > From: "W B Hacker" <[EMAIL PROTECTED]> > To: "exim users" <[email protected]> > Sent: Wednesday, August 30, 2006 10:17 AM > Subject: Re: [exim] R: Exim4 And outgoing Filters > > >> Davide Minardi wrote: >> >>> ok the problem is in the last chunk of code ... sent_archive_delivery... >>> + >>> Error message : >>> router sent_archive_delivery : cannot find rouiter driver " appendfile " >>> ..invalid new config file ----- bla bla bla >>> >>> ;???? >> >> Cut and paste that whole section - unaltered. No need to obfuscate - >> there >> is >> noting all that sensitive in the router/transport section. >> >> I suspect you have a faulted line-break, missing colon, or extraneous >> '#'. >> >> Do also, from the CLI: >> >> exim -bV >> >> (uppercase'V' there) >> >> And paste that too. >> >> Waitin' >> >> Bill >> >> >> -- >> ## List details at http://www.exim.org/mailman/listinfo/exim-users >> ## Exim details at http://www.exim.org/ >> ## Please use the Wiki with this list - http://www.exim.org/eximwiki/ >> > > > -- > ## List details at http://www.exim.org/mailman/listinfo/exim-users > ## Exim details at http://www.exim.org/ > ## Please use the Wiki with this list - http://www.exim.org/eximwiki/ > -- ## List details at http://www.exim.org/mailman/listinfo/exim-users ## Exim details at http://www.exim.org/ ## Please use the Wiki with this list - http://www.exim.org/eximwiki/
