I fear that I didn't include sufficient information with my original
message for which I apologize.
>X-Sender: [EMAIL PROTECTED]
>X-Mailer: QUALCOMM Windows Eudora Pro Version 4.2.0.58
>Date: Mon, 06 Mar 2000 19:23:41 -0500
>To: [EMAIL PROTECTED]
>From: "Stephen P. Molnar, Ph.D." <[EMAIL PROTECTED]>
>Subject: [expert] Modem Problem
>Sender: [EMAIL PROTECTED]
>Reply-To: [EMAIL PROTECTED]
>X-RCPT-TO: <[EMAIL PROTECTED]>
>
>I've just reinstalled Mandrake Helios on my pentium platform. I have a
>Zoom 56K PCI Faxmodem that used to work. The boot process sets up the ISA
>PnP devices, but when I look for the modem with kppp I get a message that
>the modem is busy.
>
>Help will be appreciated.
>
>Thanks in advance.
I should have elaborated on my statement that it used to work, it did work
on another platform running Linux from which I moved the modem.
Further isapnpconf found the card and generated the following conf file:
# $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier b6 ff ff ff ff 80 71 93 04
# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier b6 ff ff ff ff 80 71 93 04)
# Vendor Id ADS7180, No Serial Number (-1), checksum 0xB6.
# Version 1.0, Vendor version 1.0
# ANSI string -->Analog Devices AD1816<--
#
# Logical device id ADS7180
# Device support I/O range check register
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ADS7180/-1 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# IRQ 5 or 7.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 1))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0100) (CHECK))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# IRQ 5 or 7.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 1))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0100) (CHECK))
# *** ERROR *** No DMA channel specified!
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 4))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0100) (CHECK))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0100) (CHECK))
# *** ERROR *** No DMA channel specified!
# 8 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 4))
# End dependent functions
(NAME "ADS7180/-1[0]{Analog Devices AD1816}")
# (ACT Y)
))
#
# Logical device id ADS7181
# Device support I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ADS7180/-1 (LD 1
# Compatible device id PNPb006
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100) (CHECK))
# End dependent functions
(NAME "ADS7180/-1[1]{Analog Devices AD1816}")
# (ACT Y)
))
#
# Logical device id ADS7182
# Device support I/O range check register
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3e
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ADS7180/-1 (LD 2
# Compatible device id PNPb02f
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0xfff8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100) (CHECK))
# End dependent functions
(NAME "ADS7180/-1[2]{Analog Devices AD1816}")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Again, sorry for my earlier ommission, and, also, for the length of this
message.
Thanks in advance.
---------------------------------------------------------------
Stephen P. Molnar, Ph.D. Life is a fuzzy set
Foundation for Chemistry Stochastic and multivariant
614.486.4076
