Den tor, 18 maj 2000 skrev du:
> I've just decided to try Red Hat 6.2, and was dissapointed to find that it
> still doesn't install my SiS 6326 video correctly, so Mandrake 7 is still,
> AFAIK, the only Linux distro that can do it first try! Congratulations Mandrake!
>
> Also, Red Hat did not recognise my CDrw as a burner, and just installed it as a
> CDrom. Mandrake spotted the burner and installed the ide-scsi stuff to set it
> up (even though there was a simple bug in the /dev assignments) Again, Mandrake
> rules!
>
> Anyway, I now have a system that boots both Mdk & Red Hat, but have some funny
> problems, which I have think I have seen answered before on the list, but can't
> find in the archives.
>
> Firstly, my setup:
>
> hda1 fat32 Windows 95, 5Gb
> hda2 Linux Red Hat / 1.2Gb
> hdb1 fat32 used by Windows 95 850Mb
> hdb5 Linux Mandrake 3Gb
> hdb6 Linux swap 256Mb
> hdc ide CDrom
> hdd ide CDrw
>
> The problems:
>
> 1) Before the addition of the Red Hat partition, Mandrake recognised the CDrw
> properly (although I have had problems burning, but thats another story...)
> Now, however, I get a "the kernel does not recognise /dev/cdrom2 as a block
> device" error when I boot Mandrake. This happens whether I boot from lilo on
> hda or from the boot disk I made at installation.
>
> 2) Lilo when installed by the Red Hat installation using the following
> lilo.conf file:
>
> boot=/dev/hda
> map=/boot/map
> install=/boot/boot.b
> prompt
> timeout=50
> linear
> default=windows
>
> image=/boot/vmlinuz-2.2.14-5.0
> label=redhat
> read-only
> root=/dev/hda2
> append="mem=96M"
>
> other=/dev/hda1
> label=windows
>
> image=/boot/vmlinuz
> label=linux
> root=/dev/hdb5
> append="hdd=ide-scsi mem=96M"
> read-only
>
> boots redhat & windows OK, but if I select linux (mandrake), I get an error that
> modules.dep can't be found. Mandrake still starts, but I have lots of red FAILs
> at boot time, eg eth0
>
> 3) If I install lilo from Mandrake, using
>
> boot=/dev/hda
> map=/boot/map
> install=/boot/boot.b
> vga=normal
> default=windows
> keytable=/boot/us.klt
> prompt
> timeout=50
> #message=/boot/message
> other=/dev/hda1
> label=windows
> table=/dev/hda
> image=/boot/vmlinuz
> label=linux
> root=/dev/hdb5
> append="hdd=ide-scsi mem=96M"
> read-only
>
> image=/boot/vmlinuz-2.2.14-5.0
> label=redhat
> read-only
> root=/dev/hda2
> append="mem=96M"
>
> I get "open /boot/vmlinuz-2.2.14-5.0: No such file or directory". Windows &
> Mandrake boot OK (except for Problem 1) but no Red Hat.
>
> So I guess I have screwed something! How do I fix it???
>
> -- [EMAIL PROTECTED]
--
You'll have to run lilo from the RedHat partition. And also copy the Mandrake
kernel image to the root directory of RedHat (or boot-dir if you name it so in
lilo.conf). I can send you my lilo.conf if you don't manage to do what you
intend to. I am running RedHat 6.2 from /dev/hda2 and Mandrake from /dev/hda7
and Windows from /dev/hda1.
Have anybody other solutions?
[EMAIL PROTECTED]
