When I had Mandrake 7.0 - all worked fine with exactly the same equipment!!!
Since 7.1 & 7.2 - I am having nothing but problems with bus resets and
timeouts.
Using latest Adaptec BIOS - also works fine with M$ OS's . . . (go figure!)
Here's a snippet from dmesg:
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 0/14/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Cables present (Int-50 YES, Int-68 YES, Ext-68 NO)
(scsi0) Downloading sequencer code... 422 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
Vendor: IBM Model: DNES-309170W Rev: SA30
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:3:0) Synchronous at 20.0 Mbyte/sec, offset 15.
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
Vendor: YAMAHA Model: CRW4260 Rev: 1.0q
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 5, lun 0
Uniform CD-ROM driver Revision: 3.11
sr1: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB]
[8.7 GB]
sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
(scsi0:0:3:-1) Unexpected busfree, LASTPHASE = 0xa0, SEQADDR = 0x15d
(scsi0:0:3:-1) Unexpected busfree, LASTPHASE = 0xa0, SEQADDR = 0x15d
(scsi0:0:3:-1) Unexpected busfree, LASTPHASE = 0xa0, SEQADDR = 0x15d
(scsi0:0:3:-1) Unexpected busfree, LASTPHASE = 0xa0, SEQADDR = 0x15d
scsi : aborting command due to timeout : pid 8901, scsi0, channel 0, id
3, lun 0
SCSI host 0 abort (pid 8901) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
(scsi0:0:3:0) Synchronous at 20.0 Mbyte/sec, offset 15.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
sr0: CD-ROM not ready. Make sure you have a disc in the drive.
CD-ROM I/O error: dev 0b:00, sector 1172
scsi : aborting command due to timeout : pid 9098, scsi0, channel 0, id
3, lun 0
SCSI host 0 abort (pid 9098) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
(scsi0:0:3:0) Synchronous at 20.0 Mbyte/sec, offset 15.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
sr0: CD-ROM not ready. Make sure you have a disc in the drive.
CD-ROM I/O error: dev 0b:00, sector 1172
(scsi0:0:3:-1) Unexpected busfree, LASTPHASE = 0xa0, SEQADDR = 0x15d
scsi : aborting command due to timeout : pid 28512, scsi0, channel 0, id
3, lun
SCSI host 0 abort (pid 28512) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
(scsi0:0:3:0) Synchronous at 20.0 Mbyte/sec, offset 15.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
sr0: CD-ROM not ready. Make sure you have a disc in the drive.
CD-ROM I/O error: dev 0b:00, sector 1588
cdrom: open failed.
VFS: Disk change detected on device sr(11,0)
There is defintely a disk in the drive, but can't seem to get rid of
this problem!!! No disk change is made also!!
Any help would be appreciated!
Keep in touch with http://mandrakeforum.com:
Subscribe the "[EMAIL PROTECTED]" mailing list.
