Es Dilluns 26 Agost 2002 22:20, en Mike Graham va escriure:
> On Monday 26 August 2002 01:16 pm, Joan Tur wrote:
> That happened to me also and I went back into boot config and the entry for
> hba was unchecked and as soon as i checked it back all worked fine.
I've found the solution: lilo.conf's lba option was unchecked... don't know
why 8-?
> > I've found the following problem when running lilo:
> > ---------
> > [root@quinipc etc]# lilo
> > Fatal: geo_comp_addr: Cylinder number is too big (4479 > 1023)
> > ---------
> >
> > Won't it be possible to choose what ide drives are to be scsi emulated
> > -in order for them to be used by the recording software- ? Of course it
> > could be under expert mode...
> >
> > I'm wondering that because I was changing my ide DVD to scsi-emulated
> > O8-)
> >
> > Thanks.
> >
> > PD Here's my dmesg output:
> > -----------
> > Uniform Multi-Platform E-IDE driver Revision: 6.31
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> > idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39
> > VP_IDE: chipset revision 6
> > VP_IDE: not 100% native mode: will probe irqs later
> > VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
> > ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:pio
> > ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:DMA, hdd:pio
> > PDC20265: IDE controller on PCI bus 00 dev 80
> > PCI: Found IRQ 11 for device 00:10.0
> > PCI: Sharing IRQ 11 with 00:07.2
> > PCI: Sharing IRQ 11 with 00:07.3
> > PDC20265: chipset revision 2
> > PDC20265: not 100% native mode: will probe irqs later
> > PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
> > ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:DMA, hdf:pio
> > ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:DMA, hdh:pio
> > hda: Pioneer DVD-ROM ATAPIModel DVD-106S 012, ATAPI CD/DVD-ROM drive
> > hdc: AOPEN CD-RW CRW3248 1.15 20020520, ATAPI CD/DVD-ROM drive
> > hde: ST340016A, ATA DISK drive
> > hdg: IC35L060AVVA07-0, ATA DISK drive
> > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > ide1 at 0x170-0x177,0x376 on irq 15
> > ide2 at 0xd400-0xd407,0xd802 on irq 11
> > ide3 at 0xdc00-0xdc07,0xe002 on irq 11
> > hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63,
> > UDMA(100) hdg: 120103200 sectors (61493 MB) w/1863KiB Cache,
> > CHS=119150/16/63, UDMA(100) Partition check:
> > /dev/ide/host2/bus0/target0/lun0: [PTBL] [4865/255/63] p1 p2 < p5 p6 p7
> > p8
> >
> > > /dev/ide/host2/bus1/target0/lun0: p1 p2 < p5 p6 p7 p8 >
> >
> > -----------
--
Joan Tur. Eivissa-Spain
AOL quini2k, ICQ 11407395
www.ClubIbosim.org
Linux: usuari registrat 190.783
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakestore.com
