On 12/26/23 15:30, Devin Heitmueller wrote:
Hi Mark,
On Tue, Dec 26, 2023 at 2:58 PM Mark Filipak <markfilipak.i...@gmail.com> wrote:
Oops. Sorry. SAR for 16:9 DVD is 32/27. PAR is 3/2.
You brought up 40/33. That's a PAR? A PAR for what?
In this context SAR (Sample Aspect Ratio) and PAR (Pixel Aspect Ratio)
are equivalent.
On what planet are SAR & PAR equivalent?
Unfortunately the use of the term "SAR" is ambiguous
as people sometimes mean "Storage Aspect Ratio" or "Screen Aspect
Ratio". Using PAR avoids that ambiguity.
Yes, people misuse terms, mainly because the terms are not defined. The H.262 definitions have no
relevance in the real world.
"3.114 sample aspect ratio (SAR): This specifies the relative distance between samples. It is
defined (for the purposes of ITU-T Rec. H.262 | ISO/IEC 13818-2), as the vertical displacement of
the lines of luminance samples in a frame divided by the horizontal displacement of the luminance
samples. Thus, its units are (metres per line) ÷ (metres per sample)."
That definition applies solely to flying-spot scanners -- note that it is vertical (line-to-line)
spacing divided by horizontal (pixel-to-pixel) spacing. To everyone else, H/W is upside down.
H.262 then goes on to define a DAR that's upside down:
"3.44 display aspect ratio: The ratio height/width (in spatial measurement units such as
centimeters) of the intended display."
H.262 avoids "PAR" and "pixel aspect" altogether. There's not a mention. That was intentional. So,
to the ITU (and presumably to MPEG), PAR doesn't exist. Some call it 'pixel aspect' and some call it
'picture aspect'. Curiously, the ITU (and presumably to MPEG) define a 'picture', thusly:
"3.97 picture: Source, coded or reconstructed image data. A source or reconstructed picture consists
of three rectangular matrices of 8-bit numbers representing the luminance and two chrominance
signals. A 'coded picture' is defined in 3.21 of ITU-T Rec. H.262 | ISO/IEC 13818-2. For progressive
video, a picture is identical to a frame, while for interlaced video, a picture can refer to a
frame, or the top field or the bottom field of the frame depending on the context."
So, to the ITU (and presumably to MPEG) data is a picture. Good grief...
I would encourage you to review the following page, which has an
entire section on non-square pixels, as well as common values for NTSC
(which talks about the 10:11 and 40:33 commonly found with encoded
NTSC video):
704x480 is illegal for DVD. It either gets padded out to 720x480, or cropped to 704x469, then scaled
to 720x480, or some combination of the two methods. But 704x420 is not legal for DVDs -- there's no
such aspect choice in PES headers.
https://en.wikipedia.org/wiki/Pixel_aspect_ratio#Pixel_aspect_ratios_of_common_video_formats
Oh, no! Mister Billipedia! Hahahaha... (where people who are as ill informed as you are, get to
pontificate)
And my original question: What is "sntsc"?
‘ntsc’ 720x480
‘pal’ 720x576
‘sntsc’ 640x480
‘spal’ 768x576
While I wouldn't have gone with the nomenclature that ffmpeg uses, it
would appear the intent was for "ntsc" to be 720x480 with a DAR of 4:3
(therefore the PAR is 11:10), and "sntsc" to be 640x480 with a DAR of
4:3 (therefore the PAR is 1:1).
What ffmpeg is calling 'ntsc' & 'pal' are from film scanners targeting
pseudo-NTSC DVDs and
pseudo-PAL DVDs.
What ffmpeg is calling 'sntsc' & 'spal' don't have any relationship to NTSC and
PAL, neither film
nor broadcast, or to DVDs.
Why ffmpeg has put the letters 'ntsc' and 'pal' into 640x480 and 768x576 is a
total mystery to me
and continues the confusion many people have.
I'm sorry I brought it up. It was the marketing people who labeled DVDs as
'NTSC' or 'PAL'. FFmpeg
is just propagating that myth. I simply ran across 'sntsc' and asked myself, "What
is that?"
Frankly, I think the shortcuts were well-intentioned, but not very
well thought out. If you know what you are doing I would discourage
you from trying to use them and simply specify the real resolution and
framerate using the fps filter and/or the scale filter as needed.
Indeed. '-s 1920x1080' etc. ...It's more readable. :-)
(And note, it's W/H, the inverse of how the ITU (and presumably MPEG) defines
things.)
I'm done. ...Gee, I thought it was such a simple question: "What's 'sntsc'?"
_______________________________________________
ffmpeg-user mailing list
ffmpeg-user@ffmpeg.org
https://ffmpeg.org/mailman/listinfo/ffmpeg-user
To unsubscribe, visit link above, or email
ffmpeg-user-requ...@ffmpeg.org with subject "unsubscribe".
