Hi, I'm running ffserver with the following /etc/ffserver.conf file. [r...@test ~]# cat /etc/ffserver.conf | grep -v "^#" | grep . Port 8090 BindAddress 0.0.0.0 MaxHTTPConnections 2000 MaxClients 1000 MaxBandwidth 1000 CustomLog - NoDaemon <Feed feed1.ffm> File /tmp/feed1.ffm FileMaxSize 200K ACL allow 127.0.0.1 </Feed> <Stream test1.mpg> Feed feed1.ffm Format mpeg AudioBitRate 32 AudioChannels 1 AudioSampleRate 22050 VideoBitRate 64 VideoBufferSize 40 VideoFrameRate 3 VideoSize 160x128 VideoGopSize 12 </Stream> <Stream test.swf> Feed feed1.ffm Format swf VideoFrameRate 2 VideoIntraOnly NoAudio </Stream> <Stream stat.html> Format status ACL allow localhost ACL allow 192.168.0.0 192.168.255.255 </Stream> <Redirect index.html> URL http://www.ffmpeg.org/ </Redirect>
I run ffserver as follows: [r...@test ~]# ffserver FFserver version 0.5, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-nonfree --enable-gpl --enable-shared --enable-libamr-nb --enable-libamr-wb --enable-postproc --enable-avfilter --enable-libfaac --enable-libfaad --enable-libx264 --disable-ffplay --enable-libgsm --enable-libmp3lame --disable-demuxer=v4l --disable-demuxer=v4l2 --enable-pthreads --disable-debug libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 0 / 52.20. 0 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libpostproc 51. 2. 0 / 51. 2. 0 built on Jul 17 2009 15:36:44, gcc: 3.4.6 20060404 (Red Hat 3.4.6-9) Fri Jul 17 17:25:57 2009 Codecs do not match for stream 0 Fri Jul 17 17:25:57 2009 FFserver started. Fri Jul 17 17:26:11 2009 127.0.0.1 - - [GET] "/feed1.ffm HTTP/1.1" 200 4149 Fri Jul 17 17:26:11 2009 127.0.0.1 - - [POST] "/feed1.ffm HTTP/1.1" 200 0 and attempt to steam a 3gp video without success: [r...@test video]# ffmpeg -i media/video1.3gp http://127.0.0.1:8090/feed1.ffm FFmpeg version 0.5, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-nonfree --enable-gpl --enable-shared --enable-libamr-nb --enable-libamr-wb --enable-postproc --enable-avfilter --enable-libfaac --enable-libfaad --enable-libx264 --disable-ffplay --enable-libgsm --enable-libmp3lame --disable-demuxer=v4l --disable-demuxer=v4l2 --enable-pthreads --disable-debug libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 0 / 52.20. 0 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libpostproc 51. 2. 0 / 51. 2. 0 built on Jul 17 2009 15:36:44, gcc: 3.4.6 20060404 (Red Hat 3.4.6-9) Seems stream 0 codec frame rate differs from container frame rate: 29.97 (30000/1001) -> 25.00 (25/1) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'media/video1.3gp': Duration: 00:00:05.40, start: 0.000000, bitrate: 39 kb/s Stream #0.0(und): Video: h263, yuv420p, 176x144 [PAR 12:11 DAR 4:3], 25 tbr, 25 tbn, 29.97 tbc Stream #0.1(und): Audio: libamr_nb, 8000 Hz, mono, s16 Output #0, ffm, to 'http://127.0.0.1:8090/feed1.ffm': Stream #0.0(und): Audio: mp2, 22050 Hz, mono, s16, 32 kb/s Stream #0.1(und): Video: mpeg1video, yuv420p, 160x128, q=3-31, 64 kb/s, 1000k tbn, 3 tbc Stream #0.2(und): Video: flv, yuv420p, 160x128, q=3-31, 64 kb/s, 1000k tbn, 2 tbc Stream mapping: Stream #0.1 -> #0.0 Stream #0.0 -> #0.1 Stream #0.0 -> #0.2 [mpeg1video @ 0x879b2c0]bitrate tolerance too small for bitrate Error while opening codec for output stream #0.1 - maybe incorrect parameters such as bit_rate, rate, width or height I'm not sure what to change to get it working... any help appreciated! Thanks
_______________________________________________ ffserver-user mailing list ffserver-user@mplayerhq.hu https://lists.mplayerhq.hu/mailman/listinfo/ffserver-user
