Author: stepan Date: Fri Jan 28 10:00:15 2011 New Revision: 1257 URL: http://flashrom.org/trac/flashrom/changeset/1257
Log: Support Dediprog LEDs on devices with 2 and 3 LEDs. Signed-off-by: Stefan Reinauer <[email protected]> Acked-by: Mathias Krause <[email protected]> Modified: trunk/dediprog.c Modified: trunk/dediprog.c ============================================================================== --- trunk/dediprog.c Tue Jan 25 01:23:32 2011 (r1256) +++ trunk/dediprog.c Fri Jan 28 10:00:15 2011 (r1257) @@ -25,6 +25,7 @@ #include "programmer.h" #include "spi.h" +#define FIRMWARE_VERSION(x,y,z) ((x << 16) | (y << 8) | z) #define DEFAULT_TIMEOUT 3000 static usb_dev_handle *dediprog_handle; static int dediprog_firmwareversion; @@ -58,6 +59,50 @@ //int usb_control_msg(usb_dev_handle *dev, int requesttype, int request, int value, int index, char *bytes, int size, int timeout); +/* Set/clear LEDs on dediprog */ +#define PASS_ON (0 << 0) +#define PASS_OFF (1 << 0) +#define BUSY_ON (0 << 1) +#define BUSY_OFF (1 << 1) +#define ERROR_ON (0 << 2) +#define ERROR_OFF (1 << 2) +static int current_led_status = -1; + +static int dediprog_set_leds(int leds) +{ + int ret, target_leds; + + if (leds < 0 || leds > 7) + leds = 0; // Bogus value, enable all LEDs + + if (leds == current_led_status) + return 0; + + /* Older Dediprogs with 2.x.x and 3.x.x firmware only had + * two LEDs, and they were reversed. So map them around if + * we have an old device. On those devices the LEDs map as + * follows: + * bit 2 == 0: green light is on. + * bit 0 == 0: red light is on. + */ + if (dediprog_firmwareversion < FIRMWARE_VERSION(5,0,0)) { + target_leds = ((leds & ERROR_OFF) >> 2) | + ((leds & PASS_OFF) << 2); + } else { + target_leds = leds; + } + + ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, target_leds, NULL, 0x0, DEFAULT_TIMEOUT); + if (ret != 0x0) { + msg_perr("Command Set LED 0x%x failed (%s)!\n", leds, usb_strerror()); + return 1; + } + + current_led_status = leds; + + return 0; +} + static int dediprog_set_spi_voltage(int millivolt) { int ret; @@ -211,20 +256,26 @@ int residue = start % chunksize ? chunksize - start % chunksize : 0; int bulklen; + dediprog_set_leds(PASS_OFF|BUSY_ON|ERROR_OFF); + if (residue) { msg_pdbg("Slow read for partial block from 0x%x, length 0x%x\n", start, residue); ret = spi_read_chunked(flash, buf, start, residue, 16); - if (ret) + if (ret) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return ret; + } } /* Round down. */ bulklen = (len - residue) / chunksize * chunksize; ret = dediprog_spi_bulk_read(flash, buf + residue, start + residue, bulklen); - if (ret) + if (ret) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return ret; + } len -= residue + bulklen; if (len) { @@ -232,17 +283,31 @@ start, len); ret = spi_read_chunked(flash, buf + residue + bulklen, start + residue + bulklen, len, 16); - if (ret) + if (ret) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return ret; + } } + dediprog_set_leds(PASS_ON|BUSY_OFF|ERROR_OFF); return 0; } int dediprog_spi_write_256(struct flashchip *flash, uint8_t *buf, int start, int len) { + int ret; + + dediprog_set_leds(PASS_OFF|BUSY_ON|ERROR_OFF); + /* No idea about the real limit. Maybe 12, maybe more, maybe less. */ - return spi_write_chunked(flash, buf, start, len, 12); + ret = spi_write_chunked(flash, buf, start, len, 12); + + if (ret) + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); + else + dediprog_set_leds(PASS_ON|BUSY_OFF|ERROR_OFF); + + return ret; } int dediprog_spi_send_command(unsigned int writecnt, unsigned int readcnt, @@ -318,7 +383,7 @@ fw[1], fw[2]); return 1; } - dediprog_firmwareversion = fw[0]; + dediprog_firmwareversion = FIRMWARE_VERSION(fw[0], fw[1], fw[2]); return 0; } @@ -410,79 +475,6 @@ } return 0; } - -/* Start/stop blinking? - * Present in eng_detect_blink.log with firmware 3.1.8 - * Preceded by Command J - */ -static int dediprog_command_g(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x03, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command G failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} - -/* Something. - * Present in all logs with firmware 5.1.5 - * Always preceded by Command Receive Device String - * Always followed by Command Set SPI Voltage nonzero - */ -static int dediprog_command_h(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x05, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command H failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} -#endif - -/* Shutdown for firmware 5.x? - * This command swithces the "Pass" LED on. - * Present in all logs with firmware 5.1.5 - * Often preceded by a SPI operation (Command Read SPI Bulk or Receive SPI) - * Always followed by Command Set SPI Voltage 0x0000 - */ -static int dediprog_command_i(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x06, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command I failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} - -#if 0 -/* Start/stop blinking? - * Present in all logs with firmware 5.1.5 - * Always preceded by Command Receive Device String on 5.1.5 - * Always followed by Command Set SPI Voltage nonzero on 5.1.5 - * Present in eng_detect_blink.log with firmware 3.1.8 - * Preceded by Command B in eng_detect_blink.log - * Followed by Command G in eng_detect_blink.log - */ -static int dediprog_command_j(void) -{ - int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x07, 0x09, 0x07, NULL, 0x0, DEFAULT_TIMEOUT); - if (ret != 0x0) { - msg_perr("Command J failed (%s)!\n", usb_strerror()); - return 1; - } - return 0; -} #endif static int parse_voltage(char *voltage) @@ -584,22 +576,35 @@ return 1; } dediprog_endpoint = 2; + + dediprog_set_leds(PASS_ON|BUSY_ON|ERROR_ON); + /* URB 6. Command A. */ - if (dediprog_command_a()) + if (dediprog_command_a()) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; + } /* URB 7. Command A. */ - if (dediprog_command_a()) + if (dediprog_command_a()) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; + } /* URB 8. Command Prepare Receive Device String. */ /* URB 9. Command Receive Device String. */ - if (dediprog_check_devicestring()) + if (dediprog_check_devicestring()) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; + } /* URB 10. Command C. */ - if (dediprog_command_c()) + if (dediprog_command_c()) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; + } /* URB 11. Command Set SPI Voltage. */ - if (dediprog_set_spi_voltage(millivolt)) + if (dediprog_set_spi_voltage(millivolt)) { + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; + } buses_supported = CHIP_BUSTYPE_SPI; spi_controller = SPI_CONTROLLER_DEDIPROG; @@ -610,6 +615,8 @@ dediprog_do_stuff(); #endif + dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_OFF); + return 0; } @@ -670,10 +677,6 @@ { msg_pspew("%s\n", __func__); - /* Shutdown on firmware 5.x */ - if (dediprog_firmwareversion == 5) - if (dediprog_command_i()) - return 1; /* URB 28. Command Set SPI Voltage to 0. */ if (dediprog_set_spi_voltage(0x0)) return 1; _______________________________________________ flashrom mailing list [email protected] http://www.flashrom.org/mailman/listinfo/flashrom
