The HUDSON has different vendor & device id than SBx00. The ids are got
by lspci.
Signed-off-by: Wang Qing Pei <[email protected]>
Index: chipset_enable.c
===================================================================
--- chipset_enable.c (revision 1419)
+++ chipset_enable.c (working copy)
@@ -1052,6 +1052,7 @@
{0x1002, 0x4377, OK, "ATI", "SB400", enable_flash_sb400},
{0x1002, 0x438d, OK, "AMD", "SB600", enable_flash_sb600},
{0x1002, 0x439d, OK, "AMD", "SB700/SB710/SB750/SB850",
enable_flash_sb600},
+ {0x1002, 0x780e, OK, "AMD", "HUDSON", enable_flash_sb600},
{0x100b, 0x0510, NT, "AMD", "SC1100", enable_flash_sc1100},
{0x1022, 0x2080, OK, "AMD", "CS5536", enable_flash_cs5536},
{0x1022, 0x2090, OK, "AMD", "CS5536", enable_flash_cs5536},
Index: sb600spi.c
===================================================================
--- sb600spi.c (revision 1419)
+++ sb600spi.c (working copy)
@@ -259,8 +259,11 @@
smbus_dev = pci_dev_find(0x1002, 0x4385);
if (!smbus_dev) {
- msg_perr("ERROR: SMBus device not found. Not enabling SPI.\n");
- return ERROR_NONFATAL;
+ smbus_dev = pci_dev_find(0x1022,0x780b); /*HUDSON*/
+ if(!smbus_dev){
+ msg_perr("ERROR: SMBus device not found. Not enabling SPI.\n");
+ return ERROR_NONFATAL;
+ }
}
/* Note about the bit tests below: If a bit is zero, the GPIO is SPI.
*/
Best wishes
Wang Qing Pei
Phone: 86+018930528086
Index: chipset_enable.c
===================================================================
--- chipset_enable.c (revision 1419)
+++ chipset_enable.c (working copy)
@@ -1052,6 +1052,7 @@
{0x1002, 0x4377, OK, "ATI", "SB400", enable_flash_sb400},
{0x1002, 0x438d, OK, "AMD", "SB600", enable_flash_sb600},
{0x1002, 0x439d, OK, "AMD", "SB700/SB710/SB750/SB850", enable_flash_sb600},
+ {0x1002, 0x780e, OK, "AMD", "HUDSON", enable_flash_sb600},
{0x100b, 0x0510, NT, "AMD", "SC1100", enable_flash_sc1100},
{0x1022, 0x2080, OK, "AMD", "CS5536", enable_flash_cs5536},
{0x1022, 0x2090, OK, "AMD", "CS5536", enable_flash_cs5536},
Index: sb600spi.c
===================================================================
--- sb600spi.c (revision 1419)
+++ sb600spi.c (working copy)
@@ -259,8 +259,11 @@
smbus_dev = pci_dev_find(0x1002, 0x4385);
if (!smbus_dev) {
- msg_perr("ERROR: SMBus device not found. Not enabling SPI.\n");
- return ERROR_NONFATAL;
+ smbus_dev = pci_dev_find(0x1022,0x780b); /*HUDSON*/
+ if(!smbus_dev){
+ msg_perr("ERROR: SMBus device not found. Not enabling SPI.\n");
+ return ERROR_NONFATAL;
+ }
}
/* Note about the bit tests below: If a bit is zero, the GPIO is SPI. */
_______________________________________________
flashrom mailing list
[email protected]
http://www.flashrom.org/mailman/listinfo/flashrom
