Author: stefanct Date: Tue Jul 15 15:50:58 2014 New Revision: 1830 URL: http://flashrom.org/trac/flashrom/changeset/1830
Log: Add support for AMD Bolton chipset. SPI controller on the bolton chipset uses the same 3-bit speed settings as Yangtze, but is otherwise the same as the Hudson chips. Note that the Bolton RRG doesn't specify a speed setting for the bit setting of 0b111, so I'm assuming that it's the same setting as Yangtze. Signed-off-by: Martin Roth <[email protected]> Signed-off-by: Stefan Tauner <[email protected]> Acked-by: Stefan Tauner <[email protected]> Modified: trunk/sb600spi.c Modified: trunk/sb600spi.c ============================================================================== --- trunk/sb600spi.c Tue Jul 15 15:50:17 2014 (r1829) +++ trunk/sb600spi.c Tue Jul 15 15:50:58 2014 (r1830) @@ -51,6 +51,7 @@ CHIPSET_SB7XX, /* SP5100 too */ CHIPSET_SB89XX, /* Hudson-1 too */ CHIPSET_HUDSON234, + CHIPSET_BOLTON, CHIPSET_YANGTZE, }; static enum amd_chipset amd_gen = CHIPSET_AMD_UNKNOWN; @@ -137,6 +138,9 @@ if (rev >= 0x11 && rev <= 0x15) { amd_gen = CHIPSET_HUDSON234; msg_pdbg("Hudson-2/3/4 detected.\n"); + } else if (rev == 0x16) { + amd_gen = CHIPSET_BOLTON; + msg_pdbg("Bolton detected.\n"); } else if (rev >= 0x39 && rev <= 0x3A) { amd_gen = CHIPSET_YANGTZE; msg_pdbg("Yangtze detected.\n"); @@ -409,23 +413,11 @@ } /* See the chipset support matrix for SPI Base_Addr below for an explanation of the symbols used. - * bit 6xx 7xx/SP5100 8xx 9xx hudson1 hudson234 yangtze + * bit 6xx 7xx/SP5100 8xx 9xx hudson1 hudson234 bolton/yangtze * 18 rsvd <- fastReadEnable ? <- ? SpiReadMode[0] * 29:30 rsvd <- <- ? <- ? SpiReadMode[2:1] */ - if (amd_gen >= CHIPSET_YANGTZE) { - tmp = mmio_readb(sb600_spibar + 0x20); - msg_pdbg("UseSpi100 is %sabled\n", (tmp & 0x1) ? "en" : "dis"); - if ((tmp & 0x1) == 0) { - rmmio_writeb(tmp | 0x1, sb600_spibar + 0x20); - tmp = mmio_readb(sb600_spibar + 0x20) & 0x1; - if (tmp == 0) { - msg_perr("Enabling Spi100 failed.\n"); - return 1; - } - msg_pdbg("Enabling Spi100 succeeded.\n"); - } - + if (amd_gen >= CHIPSET_BOLTON) { static const char *spireadmodes[] = { "Normal (up to 33 MHz)", /* 0 */ "Reserved", /* 1 */ @@ -434,7 +426,7 @@ "Dual IO (1-2-2)", /* 4 */ "Quad IO (1-4-4)", /* 5 */ "Normal (up to 66 MHz)", /* 6 */ - "Fast Read", /* 7 */ + "Fast Read", /* 7 (Not defined in the Bolton datasheet.) */ }; tmp = mmio_readl(sb600_spibar + 0x00); uint8_t read_mode = ((tmp >> 28) & 0x6) | ((tmp >> 18) & 0x1); @@ -448,11 +440,25 @@ msg_pdbg("Setting read mode to \"%s\" succeeded.\n", spireadmodes[read_mode]); } - tmp = mmio_readw(sb600_spibar + 0x22); /* SPI 100 Speed Config */ - msg_pdbg("NormSpeedNew is %s\n", spispeeds[(tmp >> 12) & 0xf].name); - msg_pdbg("FastSpeedNew is %s\n", spispeeds[(tmp >> 8) & 0xf].name); - msg_pdbg("AltSpeedNew is %s\n", spispeeds[(tmp >> 4) & 0xf].name); - msg_pdbg("TpmSpeedNew is %s\n", spispeeds[(tmp >> 0) & 0xf].name); + if (amd_gen >= CHIPSET_YANGTZE) { + tmp = mmio_readb(sb600_spibar + 0x20); + msg_pdbg("UseSpi100 is %sabled\n", (tmp & 0x1) ? "en" : "dis"); + if ((tmp & 0x1) == 0) { + rmmio_writeb(tmp | 0x1, sb600_spibar + 0x20); + tmp = mmio_readb(sb600_spibar + 0x20) & 0x1; + if (tmp == 0) { + msg_perr("Enabling Spi100 failed.\n"); + return 1; + } + msg_pdbg("Enabling Spi100 succeeded.\n"); + } + + tmp = mmio_readw(sb600_spibar + 0x22); /* SPI 100 Speed Config */ + msg_pdbg("NormSpeedNew is %s\n", spispeeds[(tmp >> 12) & 0xf].name); + msg_pdbg("FastSpeedNew is %s\n", spispeeds[(tmp >> 8) & 0xf].name); + msg_pdbg("AltSpeedNew is %s\n", spispeeds[(tmp >> 4) & 0xf].name); + msg_pdbg("TpmSpeedNew is %s\n", spispeeds[(tmp >> 0) & 0xf].name); + } } else { if (amd_gen >= CHIPSET_SB89XX && amd_gen <= CHIPSET_HUDSON234) { bool fast_read = (mmio_readl(sb600_spibar + 0x00) >> 18) & 0x1; _______________________________________________ flashrom mailing list [email protected] http://www.flashrom.org/mailman/listinfo/flashrom
