Hello,
I have problem after trying flash QNAP TS-453A
[~] # hal_app --se_sys_get_system_info
NAS display name = TS-453A
NAS CPU_0 Model Name = Intel(R) Celeron(R) CPU N3150 @ 1.60GHz
NAS CPU_0 running speed = 1601 MHz
=== Slot1 Mem Info. Channed Id is 1, Slot Addr is 0x50 ===
Mem Type: DDR3_SDRAM
Module Type: SO_DIMM
Ram Size: 2048 MB
Speed: 1600 MHz
Module Manufacture: Transcend Information
ECC Support: No
=== Slot2 Mem Info. Channed Id is 2, Slot Addr is 0x51 ===
Mem Type: DDR3_SDRAM
Module Type: SO_DIMM
Ram Size: 2048 MB
Speed: 1600 MHz
Module Manufacture: Transcend Information
ECC Support: No
[~] # dmidecode -s bios-version
QX47AR12
[~] # hal_app --get_ec_version
QX47EC23[~] # cd /share/Public/Temp
[/share/Public/Temp] # chmod +x flashrom
[/share/Public/Temp] # ./flashrom -p
internal:laptop=this_is_not_a_laptop -w QX47AR50.bin
flashrom v0.9.8-unknown on Linux 4.2.8 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK.
Active config mode, unknown reg 0x20 ID: 85.
Please send the output of "flashrom -V -p internal" to
[email protected] with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
========================================================================
WARNING! You may be running flashrom on an unsupported laptop. We could
not detect this for sure because your vendor has not setup the SMBIOS
tables correctly. You can enforce execution by adding
'-p internal:laptop=this_is_not_a_laptop' to the command line, but
please read the following warning if you are not sure.
Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See the manpage and http://www.flashrom.org/Laptops for details.
If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Proceeding anyway because user forced us to.
Found chipset "Intel Braswell".
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware
with it,
then please email a report to [email protected] including a verbose
(-V) log.
Thank you!
Enabling flash write... Warning: BIOS region SMM protection is enabled!
Warning: Setting Bios Control at 0x0 from 0x2a to 0x09 failed.
New value is 0x2a.
Warning: SPI Configuration Lockdown activated.
OK.
Found Macronix flash chip "MX25U6435E/F" (8192 kB, SPI) mapped at
physical address 0xff800000.
===
This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE
The test status of this chip may have been updated in the latest development
version of flashrom. If you are running the latest development version,
please email a report to [email protected] if any of the above
operations
work correctly for you with this flash chip. Please include the flashrom log
file for all operations you tested (see the man page for details), and
mention
which mainboard or programmer you tested in the subject line.
Thanks for your help!
Reading old flash chip contents... done.
Erasing and writing flash chip... Transaction error!
spi_block_erase_20 failed during command execution at address 0x300000
Reading current flash chip contents... done. Looking for another erase
function.
spi_block_erase_52 failed during command execution at address 0x300000
Reading current flash chip contents... done. Looking for another erase
function.
spi_block_erase_d8 failed during command execution at address 0x300000
Reading current flash chip contents... done. Looking for another erase
function.
spi_chip_erase_60 failed during command execution
Reading current flash chip contents... done. Looking for another erase
function.
spi_chip_erase_c7 failed during command execution
Looking for another erase function.
No usable erase functions left.
FAILED!
Uh oh. Erase/write failed. Checking if anything has changed.
Reading current flash chip contents... done.
Apparently at least some data has changed.
Your flash chip is in an unknown state.
Get help on IRC at chat.freenode.net (channel #flashrom) or
mail [email protected] with the subject "FAILED: <your board name>"!
-------------------------------------------------------------------------------
DO NOT REBOOT OR POWEROFF!
[/share/Public/Temp] #
what I can do now?
Br
Martin Gawryš
Dne 30.3.2017 v 17:40 QNAP Technical Support napsal(a):
Dobry den,
vyvojari potvrdili ze problem byl vyresen v poslednim BIOSu pro tuto
NAS, muzete na nej zkusit updatnout? Prikladam detailni navod - budete
k nemu potrebovat pristup k SSH NASky, tam se dostanete napr. pres
PuTTY ( www.putty.org <http://www.putty.org> ) - port 22, uzivatel admin:
Please follow below SOP to flash BIOS for TS-X53A.
Preparation:
*
Download package from below link:
N3150: http://download.qnap.com/Storage/tsd/bios/TS-x53A_QX47AR50.zip
N3160: http://download.qnap.com/Storage/tsd/bios/TS-x53A_QX47AR25.zip
*
Extract the compressed file, please upload below 3 files to shared
folder, “Public”
N3150: flashrom, QX47AR50.bin and QX47EC20.BIN
N3160: flashrom, QX47AR25 and QX47EC20.BIN
*
Follow below commands to complete the BIOS flash procedure.
1. Check current CPU name
There are two version of BIOS, QX47AR50.bin andQX47AR25.bin,
corresponding to N3150and N3160respectively.
N3150->QX47AR50.bin
N3160 -> QX47AR25.bin
CAUTION: Do NOT apply wrong version of BIOS, it will brick your machine.
[~] # hal_app --se_sys_get_system_info
NAS display name = TS-453A
NAS CPU_0 Model Name = Intel(R) Celeron(R) CPU N3150 @ 1.60GHz
NAS CPU_0 running speed = 1601 MHz
=== Slot1 Mem Info. Channed Id is 1, Slot Addr is 0x50 ===
Mem Type: DDR3_SDRAM
Module Type: SO_DIMM
Ram Size: 2048 MB
Speed: 1600 MHz
Module Manufacture: Transcend Information
=== Slot2 Mem Info. Channed Id is 2, Slot Addr is 0x51 ===
Mem Type: DDR3_SDRAM
Module Type: SO_DIMM
Ram Size: 2048 MB
Speed: 1600 MHz
Module Manufacture: Transcend Information
2. Check current BIOS and EC version
CAUTION: User mustdowngrade EC firmware if EC version is higher than
QX47EC20
[~] # dmidecode -s bios-version
QX47AD20
[~] # hal_app --get_ec_version
QX47EC22
3. Update BIOS
For different CPU, user should give different parameter to flashrom.
N3150: ./flashrom -p internal:laptop=this_is_not_a_laptop -w QX47AR50.bin
N3160: ./flashrom -p internal:laptop=this_is_not_a_laptop -w QX47AR25.bin
CAUTION: Do NOT apply wrong version of BIOS, it will brick your machine.
[~] # cd /share/Public
[/share/Public] # chmod +x flashrom
[/share/Public] # ./flashrom -p internal:laptop=this_is_not_a_laptop
-w QX47AR50.bin
flashrom v0.9.8-unknown on Linux 3.19.8 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK.
Active config mode, unknown reg 0x20 ID: 85.
Please send the output of "flashrom -V -p internal" to
[email protected] with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
========================================================================
WARNING! You may be running flashrom on an unsupported laptop. We could
not detect this for sure because your vendor has not setup the SMBIOS
tables correctly. You can enforce execution by adding
'-p internal:laptop=this_is_not_a_laptop' to the command line, but
please read the following warning if you are not sure.
Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See the manpage and http://www.flashrom.org/Laptops for details.
If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Proceeding anyway because user forced us to.
Found chipset "Intel Braswell".
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware
with it,
then please email a report to [email protected]
<mailto:[email protected]> including a verbose (-V) log.
Thank you!
Enabling flash write... OK.
Found Macronix flash chip "MX25U6435E/F" (8192 kB, SPI) mapped at
physical address 0xff800000.
===
This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE
The test status of this chip may have been updated in the latest
development
version of flashrom. If you are running the latest development version,
please email a report to [email protected]
<mailto:[email protected]> if any of the above operations
work correctly for you with this flash chip. Please include the
flashrom log
file for all operations you tested (see the man page for details), and
mention
which mainboard or programmer you tested in the subject line.
Thanks for your help!
Reading old flash chip contents... done.
Erasing and writing flash chip... Erase/write done.
Verifying flash... VERIFIED.
4. Update EC firmware
CAUTION: User mustdowngrade EC firmware if EC version higher than QX47EC20
[/share/Public] # hal_app --update_ec_fw file=QX47EC20.BIN
5. Reboot NAS with below command.
[/share/Public] # hal_app --reset_ec_fw
6. After the reboot, check BIOS/EC version again
[~] # dmidecode -s bios-version
QX47AR50
[~] # hal_app --get_ec_version
QX47EC20
7. Done.
Best regards,
Lukas Zemina
---------------------------
Disclaimer:
Our advice is strictly limited to the question(s) asked and is based
on the information provided to us. QNAP Systems Inc. does not assume
any responsibility or liability for the advice given and shall not be
liable for any direct, indirect, special, incidental or consequential
damages in connection with the use of this information. Any promise,
action or solution we make for your questions does not constitute an
agreement between you and QNAP unless a written agreement signed by
authorized representative is provided. Please always back up your
data. For more information, including technical information updates,
please visit our website at http://www.qnap.com/
Ticket Details
------------------------------------------------------------------------
Ticket ID: ZJW-196-68375
Department: Europe - Central & Eastern Europe, Greece, Russia
Helpdesk: https://helpdesk.qnap.com/index.php?
_______________________________________________
flashrom mailing list
[email protected]
https://mail.coreboot.org/mailman/listinfo/flashrom
