I'm trying to use flashrom 1.2 on a GIGABYTE GA-H270N-WIFI motherboard with DualBIOS feature. According to manpage, one can check which of the two flash chips is currently selected like this:
flashrom -p internal:dualbiosindex This error message is shown instead: Unhandled programmer parameters: dualbiosindex Aborting. Error: Programmer initialization failed. If I don't specify the dualbiosindex parameter this message is shown: Found Programmer flash chip "Opaque flash chip" (16384 kB, Programmer-specific) mapped at physical address 0x0000000000000000. No operations were specified. I'm also able to dump a valid copy of the firmware without problems, but I'm unable to control which of the two flash chips are being read (or written). flashrom -V -p internal:dualbiosindex ======================================================================= flashrom 1.2 on Linux 4.19.164_1 (x86_64) flashrom is free software, get the source code at https://flashrom.org flashrom was built with libpci 3.7.0, GCC 9.3.0, little endian Command line (3 args): flashrom -V -p internal:dualbiosindex Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns). Initializing internal programmer /sys/class/mtd/mtd0 does not exist No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Desktop" DMI string system-manufacturer: "Gigabyte Technology Co., Ltd." DMI string system-product-name: "H270N-WIFI" DMI string system-version: "Default string" DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd." DMI string baseboard-product-name: "H270N-WIFI-CF" DMI string baseboard-version: "x.x" Found ITE Super I/O, ID 0x8686 on port 0x2e Found chipset "Intel H270" with PCI ID 8086:a2c4. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom@flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... BIOS_SPI_BC = 0xa88: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x0 (SPI) Top Swap: not enabled SPI Read Configuration: prefetching enabled, caching enabled, BIOS_CNTL = 0x89: BIOS Lock Enable: disabled, BIOS Write Enable: enabled SPIBAR = 0x00007fbbfbbcb000 (phys = 0xfe010000) 0x04: 0xe004 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=1, SCIP=0, PRR34_LOCKDN=0, WRSDIS=0, FDOPSS=1, FDV=1, FLOCKDN=1 SPI Configuration is locked down. Reading OPCODES... done 0x06: 0x3f00 (HSFC) HSFC: FGO=0, HSFC=0, WET=0, FDBC=63, SME=0 0x0c: 0x00000000 (DLOCK) DLOCK: BMWAG_LOCKDN=0, BMRAG_LOCKDN=0, SBMWAG_LOCKDN=0, SBMRAG_LOCKDN=0, PR0_LOCKDN=0, PR1_LOCKDN=0, PR2_LOCKDN=0, PR3_LOCKDN=0, PR4_LOCKDN=0, SSEQ_LOCKDN=0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-write. 0x58: 0x0fff0200 FREG1: BIOS region (0x00200000-0x00ffffff) is read-write. 0x5C: 0x01ff0003 FREG2: Management Engine region (0x00003000-0x001fffff) is read-write. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0xa0: 0x90 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=1 0xa1: 0xfe0000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=6 0xa4: 0x0000 (PREOP) 0xa6: 0x0000 (OPTYPE) 0xa8: 0x00000000 (OPMENU) 0xac: 0x00000000 (OPMENU+4) 0xc4: 0xf3d82005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xc8: 0x20452045 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 Enabling hardware sequencing because some important opcode is locked. OK. Unhandled programmer parameters: dualbiosindex Aborting. Error: Programmer initialization failed. Restoring PCI config space for 00:1f:5 reg 0xdc ======================================================================= Any ideas why this happens? Thanks. Best regards, Pete Smith _______________________________________________ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org
