Hello, I'm not an active member of flashrom "team", but in my life i have done some flash rounds
YOU have choose this version for the bios and for what I can see: FW6A/B/C6-210621YKBR6L12*Please see notes above before flashing. New Logo, Added Support for Intel i210/i211 NICsJune 30, 2021 is NOT the best choose. In my opinion the right choose should be : FW6A/B/C/D/E6-210827KBR6L 1.50Unified BIOS for FW6A/B/C/D/ENovember 18, 2021373da4fb5c93c964b7441bc6ee9580bfacb140d9bc25049cd4fdfef4a4076780 or in old vesion this: FW6E6E201203KBR6L 1.32Initial Released VersionDecember 3, 2020 I have take all this information from https://protectli.com/kb/bios-versions-for-the-vault/?intsrc=eu as you can easy check it out... I don't know actualy what is your PC state, but if you have a #bash terminal active "I THINK" you can try a soft shutdown with: :$ sudo poweroff or :$ sudo shutdown -h now or :$ sudo shutdown -h +0 also without "sudo" (this because I don't know if you actualy are working like superuser or not). Keep on mind that this is ONLY what I should do in your case, but I am NOBODY to assure you that this will solve your problem !!! TAKE CARE (or wait for other staff suggetion) Reagards Il giorno mer, 18/05/2022 alle 00.32 +0000, John Caltry via flashrom ha scritto: > Hello, > > Ubuntu 20.04 boot from USB (try Ubuntu) and attempted install using > Protectli Flashli. Cut and paste follows, any advice is appreciated! > > John > > > > > \ == \ /\ == \ /\ __ \ /\__ _\ /\ ___\ /\ ___\ /\__ _\ > /\ \ /\ \ > \ \ _-/ \ \ __< \ \ \/\ \ \/_/\ \/ \ \ __\ \ \ \____ \/_/\ > \/ \ \ \____ \ \ \ > \ \_\ \ \_\ \_\ \ \_____\ \ \_\ \ \_____\ \ \_____\ \ > \_\ \ \_____\ \ \_\ > \/_/ \/_/ /_/ \/_____/ \/_/ \/_____/ \/_____/ > \/_/ \/_____/ \/_/ > _____________________________________________________________________ > ____________________ > > > =========================================FlashLi===================== > ==================== > --Version 1.1.20-- > > Device: Protectli fw6e > CPU: Intel(R) Core(TM) i7-8550U CPU @ 1.80GHz > BIOS Mode: BIOS > > Available BIOS: > > [1]: ami (FW6_all_YKBR6L12.bin) > [2]: coreboot (protectli_all_fw6_vault_kbl_v1.0.14.rom) > > Enter the [#] of an image file, or [0] to quit. Flahing will not > begin yet > > 2 > > ********************************************!************************ > ******************** > Are you sure you would like to flash this device? > > Flashing new firmware onto any hardware is potentially dangerous in > that if the > procedure is interrupted or otherwise not able to complete, your > hardware may be rendered > useless. Please proceed with caution. If there are any questions, > please contact > Protectli support BEFORE proceeding. > > Unless there is a compelling reason to update the BIOS, we recommend > to stay with your > current known working BIOS version > > ********************************************!************************ > ******************** > > Acknowledgement Yes [Y]: y > > flashrom v1.2-326-gf57486e on Linux 5.13.0-30-generic (x86_64) > flashrom is free software, get the source code at > https://flashrom.org > > Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns). > Found chipset "Intel Kaby Lake U w/ iHDCP2.2 Prem.". > Enabling flash write... SPI Configuration is locked down. > Enabling hardware sequencing because some important opcode is locked. > OK. > Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer- > specific) mapped at physical address 0x0000000000000000. > Reading ich descriptor... done. > Using region: "bios". > Reading old flash chip contents... done. > Erasing and writing flash chip... Erase/write done. > Verifying flash... FAILED at 0x00103056! Expected=0xff, Found=0xc5, > failed byte count from 0x00000000-0x007fffff: 0x99c > Your flash chip is in an unknown state. > Get help on IRC at chat.freenode.net (channel #flashrom) or > mail flashrom@flashrom.org with the subject "FAILED: <your board > name>"! > ------------------------------------------------------------------- > ------------ > DO NOT REBOOT OR POWEROFF! > BIOS Flash failed, is this script running with root permissions? > Please try again, but if problems persist, please let us know. > TODO: Collect info and display instructions on how to submit a Github > issue. > _______________________________________________flashrom mailing list > -- flashrom@flashrom.org > To unsubscribe send an email to flashrom-le...@flashrom.org
_______________________________________________ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org