Here are some settings I use for the DSP NR, ANF, NB's For ME these settings work better then the Defaults and I haven't done much experimenting on CW with theses settings, but your mileage will vary.
PowerSDR settings after a new Database is loaded DSP settings NR ANF Buffer NB 40 68 Phone 20 30 50 RX 4096 NB2 15 25 TX 2048 15 73's Bret WX7Y -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Gary Warner Sent: Tuesday, December 14, 2010 4:10 PM To: Tim Ellison Cc: [email protected] Subject: Re: [Flexradio] DSP and ANR and filter configuration Tim, OK, I looked at the two articles. The first article, 50437, PowerSDR Buffers and Sample Rate***. *I think that I understand that we want to run SDR with the smallest sample rate and highest buffer that we and our computer can stand. Is that correct? Anything else? The second article, 50439, DSP Window Functions in PowerSDR is not clear to me. What direction in the making settings am I to understand from the theory? I am assuming that we want the minimum bleed-through of the signal, and that Blackman-Harris does that best. Am I missing something else? Gary On 12/14/2010 2:22 PM, Tim Ellison wrote: > I forgot to add these KB references > http://kc.flexradio.com/KnowledgebaseArticle50437.aspx > http://kc.flexradio.com/KnowledgebaseArticle50439.aspx > > > > -Tim > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Tim Ellison > Sent: Tuesday, December 14, 2010 5:17 PM > To: Gary Warner; [email protected] > Subject: Re: [Flexradio] DSP and ANR and filter configuration > > Download the FLEX-3000 Owner's Manual (it is the one with the latest > PowerSDR info) and read the section on the DSP tab. (page 80) > http://support.flexradio.com/Downloads.aspx?id=271 > > > -Tim > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Gary Warner > Sent: Tuesday, December 14, 2010 4:55 PM > To: [email protected] > Subject: [Flexradio] DSP and ANR and filter configuration > > I see that there are default settings that are in place for DSP, ANR and the various filters. Is there some guidance in making changes to improve them for my particular setup? I am interested in SSB for the moment, but the answer can certainly cover CW and other modes as well. I am running SDR 2.0.16. > > Gary Warner > WG1I > _______________________________________________ > FlexRadio Systems Mailing List > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flexradio.com/ Homepage: > http://www.flexradio.com/ > > _______________________________________________ > FlexRadio Systems Mailing List > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flexradio.com/ Homepage: > http://www.flexradio.com/ _______________________________________________ FlexRadio Systems Mailing List [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. _______________________________________________ FlexRadio Systems Mailing List [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
