Unless an existing cable definition(s) get over written in the registry
when VACshuts down (I didn't test for that condition)
You can also open up the VAC control panel after doing the reg file
update and click on the Restart button.
Tim Ellison
On 3/18/2012 12:18 PM, Sheldon Hartling wrote:
You should see the new cables after a reboot.
73, Sheldon VE1GPY
From: Jerry Flanders<[email protected]>
Date: Sun, 18 Mar 2012 12:03:42 -0400
To:<[email protected]>
Cc:<[email protected]>
Subject: Re: [Flexradio] VAC 4.11 Registry Import file
WOW - 15 more copies were downloaded this morning since I asked about it
here.
Anybody installed it yet? I did but after checking to see how it turned
out I see I only got my standard two cables. Maybe I did something wrong.
I am in the middle of the BARTG RTTY contest now so will wait until
later to find my problem.
I had a gradually increasing latency delay with VAC 4.09 which was a
nuisance in lengthy contest running - had to periodically turn VAC
off/on to fix it (didn't always work). After running an hour I haven't
noticed the problem yet, so maybe that is gone (fingers crossed).
Jerry W4UK
On 3/18/2012 10:45 AM, Tim Ellison, W4TME wrote:
That is exactly correct.
Tim Ellison, W4TME
Product Management, Sales& Support
FlexRadio Systems^(TM)
4616 W Howard Ln, Suite 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: [email protected]<mailto:[email protected]>
Web: www.flexradio.com<http://www.flexradio.com>
logo
On 3/18/2012 9:49 AM, Jerry Flanders wrote:
So to use it, I could install the VAC 4.11 panel (without creating
any cables yet), then execute this file, reboot, and my VAC cables
are ready to go without further tweaking, right? Sounds like a BIG
help. Thanks
Jerry W4UK
On 3/18/2012 8:55 AM, Tim Ellison, W4TME wrote:
You don't even have to have VAC4 loaded. It creates the registry
entries for the cables definitions described below when you install
VAC4 or if you have it installed, they are created after you reboot.
It will remove any existing cable definitions if you already have
VAC4 installed.
Tim Ellison, W4TME
Product Management, Sales& Support
FlexRadio Systems^(TM)
4616 W Howard Ln, Suite 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: [email protected]<mailto:[email protected]>
Web: www.flexradio.com<http://www.flexradio.com>
logo
On 3/18/2012 8:11 AM, Jerry Flanders wrote:
This *VAC 4.11 Registry Import* file appeared 3/17 on the flex
downloads page.
Description: "This file is a Windows Registry file that will create
seven (7) VAC 4.11 cables. The first 6 are used with PowerSDR in
the VAC configuration and the seventh is used as the default sound
card device if you do not have an active sound card in you PC"
It is from an unidentified 3rd party.
I am guessing we install VAC 4.11 then run this to set the
necessary cables automatically(?)
Anybody used this?
Jerry W4UK
_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
