Realmente nose en que manual esta, pero en el infocenter tenes toda la
explicación, aqui te dejo lo que necesitas.
Saludos.
Sergio
Enviar comentarios | Evaluar esta página
Normal control panel functions
These instructions show how to use normal control panel functions 01 through
49. Functions 21 through 49 are available when you select the Manual mode.
The instructions you follow for function 01 or 02 depend on whether your system
uses a keystick. Also, the following instructions for functions 01 and 02
alternate between systems with a keystick and systems without a keystick.
To determine how to activate functions 01 and 02 on a control panel, complete
the following steps:
Does the control panel have an electronic keylock (a keystick)?
Yes
Go to the next step.
No
The system displays the IPL key mode (For Manual or Normal modes only). The
Auto mode and Secure mode are not supported. Follow the procedures for
functions 01 and 02 for systems without a keystick.
Insert the keystick.
Press the Mode button to select the IPL mode. Follow function 01 and 02
procedures for systems with a keystick.
Note: The function that is displayed is not activated until you press Enter on
the control panel.
To select a function number, press the Increment or Decrement button on the
control panel. To activate the function, press Enter on the control panel while
the system displays the required function number.
Function 01 - Display Selected IPL Type and IPL Speed (on Systems with a
Keystick)
This function allows you to display the selected type and speed for the next
IPL.
Display IPL types (A, B, C, or D).
Display IPL speed (F, S, SE, V=F, or V=S).
When selected, function 01 displays the currently selected IPL type and IPL
speed values (where each _ represents 1 character).
The following table shows a function 01 example with a keystick.
Function 01 on systems with a keystick
Function/data
Action or description
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll to function 01.
0 1 _ _ A _ _ _ _ _ V = F _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Valid IPL types are A, B, C, or D.
Valid IPL speed displays are F, S, SE, V=F, or V=S.
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the control panel
functions.
Function 01 - Display Selected IPL Type, Logical Key Mode, and IPL Speed (on
Systems without a Keystick)
This function allows you to display the selected IPL type, logical key mode,
and speed for the next IPL.
Display IPL types (A, B, C, or D).
Display the valid logical key modes (M or N).
Display IPL speed (F, S, SE, V=F, or V=S).
The following table shows a function 01 example on systems without a keystick.
Function 01 on systems without a keystick
Function/data
Action or description
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll to function 01.
0 1 _ _ A _ _ M _ _ V = F _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Valid IPL types are A, B, C, and D.
Valid logical key modes are Manual and Normal.
Valid IPL speed displays are F, S, SE, V=F, or V=S.
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the control panel
functions.
Function 02 with a keystick - Select IPL Type and IPL Speed Override (on
Systems with a Keystick)
Before you can use function 02, you must have the system in Manual mode. You
can change the IPL types with the system turned on or off. However, to select
the IPL speed override, you must turn off the system.
The following table shows the sequence used to select the IPL type on systems
that are turned on.
Function 02 - Select IPL type on turned-on systems with a keystick
Function/data
Action or description
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll to function 02.
0 2 _ _ A < _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to start function 02. The current IPL type is displayed with a
pointer.
0 2 _ _ B < _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the IPL types.
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the IPL type and exit function 02.
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the control panel
functions.
The following table shows the sequence used to select the IPL type and IPL
speed on systems that are turned off.
Function 02 - Select IPL type and IPL speed on turned-off systems with a
keystick
Function/Data
Action or Description
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use Increment or Decrement buttons to scroll to function 02.
0 2 _ _ A < _ _ _ _ _ _ V _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to start function 02:
The current IPL type is displayed with a pointer.
The current IPL speed is displayed.
0 2 _ _ B < _ _ _ _ _ _ V _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the IPL types and
speeds.
0 2 _ _ B _ _ _ _ _ _ _ V _ < _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the IPL type.
The current IPL type is displayed.
The current IPL speed is displayed with a pointer.
0 2 _ _ B _ _ _ _ _ _ _ S _ < _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the IPL speeds.
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the IPL speed and exit function 02.
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the control panel
functions.
Function 02 without a keystick - Select IPL type, IPL speed override, and
Logical key mode (on Systems without a Keystick)
You can use function 02 in either normal mode or manual mode. With the system
either turned on or off, this function allows you to select the IPL type and
logical key mode. Before you can select the IPL speed override, you must turn
off the system.
Turned-on systems
For turned-on systems without a keystick, function 02 is used to select the IPL
mode and logical key mode. The following table shows an example of the function
02 IPL type and logical key mode selection sequence for a turned-on system that
does not have a keystick.
Function 02 - Select IPL type and logical key mode on turned-on systems without
a keystick
Function/data
Action or description
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll to function 02.
0 2 _ _ A < _ M _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to start function 02.
The current IPL type is displayed with a pointer.
The current logical key mode is displayed.
0 2 _ _ B < _ M _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the IPL types.
0 2 _ _ B _ _ M < _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the IPL type.
0 2 _ _ B _ _ N < _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the logical key modes.
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the logical key mode and exit function 02.
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the control panel
functions.
Turned-off systems
For turned-off systems without a keystick, function 02 is used to select the
IPL type, logical key mode, and IPL speed indicators. The following table shows
an example of the function 02 IPL type, logical key mode, and IPL speed
selection sequence for a turned-off system that does not have a keystick.
Function 02 - Select IPL type, logical key mode, and IPL speed on turned-off
systems without a keystick
Function/data
Action or description
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll to function 02.
0 2 _ _ A < _ M _ _ _ _ V _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to start function 02.
The current IPL type is displayed with a pointer.
The current logical key mode is displayed.
The current IPL speed is displayed.
0 2 _ _ B < _ M _ _ _ _ V _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the IPL types.
0 2 _ _ B _ _ M < _ _ _ V _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the IPL type.
The current IPL type is displayed.
The current logical key mode is displayed with a pointer.
The current IPL speed is displayed.
0 2 _ _ B _ _ N < _ _ _ V _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the logical key modes.
0 2 _ _ B _ _ N _ _ _ _ V _ < _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the logical key mode.
The current IPL type is displayed.
The current logical key mode is displayed.
The current IPL speed is displayed with a pointer.
0 2 _ _ B _ _ N _ _ _ _ S _ < _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the IPL speeds.
0 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Press Enter to select the IPL speed and exit function 02.
0 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use the Increment or Decrement buttons to scroll through the control panel
functions.
Function 03 - Start IPL
The system enables function 03 only when the key mode is Manual and the system
is turned on.
This function starts an IPL of the selected IPL type when you press the Enter
button. The system will load all the Licensed Internal Code.
Attention: No system shutdown is performed before the initial program load
(IPL). The use of this function can cause data loss.
Function 04 - Lamp Test
This function shows whether any control panel indicators are burned out and
whether characters that are displayed on the control panel Function/Data
display are valid. When you activate this test, all the control panel lights
and indicators flash on and off.
The lamp test continues on the system control panel until you perform another
control panel function or a power procedure. The lamp test for the expansion
unit control panel is active for 25 seconds and does not flash.
Use this procedure to verify that the lights on the system control panel are
working correctly. If you cannot complete these steps, contact your service
provider.
Turn on the system.
Press the Increment or Decrement buttons on the control panel to display
function 04.
Press Enter on the control panel.
Do all of the lights and indicators on the system control panel flash on and
off?
Yes
Proceed to the next step.
No
Need to exchange the control panel or the replaceable unit that contains the
control panel function (system unit backplane (MB1) or tower card (CB1)).
Contact your service provider.
Do all the control panel lights on the expansion unit come on?
Yes
End.
No
Exchange the control panel on the expansion unit.
The lights on the system control panel are working correctly.
Function 05 - SPCN SRC
Function 05 displays information about power faults and provides informational
reference codes during disk-unit concurrent maintenance procedures. The format
for this function is as follows:
SPCN SRC formats
Function 07
Function 07 is only used during service by authorized IBM service
representatives.
Function 08 - Fast Turn Off
Function 08 is enabled only when the key mode is Manual and the system is
turned on.
Use this function when the system is suspended and you cannot perform a
turn-off operation.
The first time that you select function 08 and press Enter, the system displays
an attention SRC, 11 A1xx 8008. This SRC indicates that you selected Function
08. The second time that you select function 08 and press Enter, you confirm
the request to turn off. To perform a fast turn off, see Stopping the system.
Attention: No system shutdown is performed before the initial program load
(IPL). The use of this function can cause loss of data.
Attention: If the system password was changed at the most recent IPL,
performing a fast turn off might cause that new password information to be lost.
Functions 09 to 10 - Reserved
These functions are reserved for future control panel operations.
Functions 11 to 19 - System Reference Code (SRC)
Functions 11 though 19, if enabled, represent the words of the SRC.
You must record SRC information for error reporting and contact your service
provider.
Function 20 - System type, model, feature code, hardware level, and IPL path
description
This function displays the machine type, model, processor feature code,
hardware level, and IPL path description in the following format:
t m m m c c c c _ _ _ _ _ _ _ _
h h h h _ _ _ _ i i i i i i i i
Values for t indicate the machine type:
1
9401
2
9402
4
9404
6
9406
Values for m indicate the model:
mmm
Model number (for example, 820)
Values for c indicate the system processor feature code:
cccc
Processor feature code (for example, 23A4)
Values for hhhh indicate the system processor hardware level:
hhhh
Processor hardware level (for example, 1025)
Values for iiiiiiii indicate the description of the system turn on or restart
path:
iiiiiiii
The restart path description (for example, 00 000 001 indicates that the system
was turned on by using the white button on the control panel).
You should record this information with the SRC.
Function 21 - Make DST Available
This function makes DST available on the system console display. The Use
Dedicated Service Tools (DST) display appears on the primary or alternative
console.
To exit DST and return to the operating system, select the Resume operating
system display option on the Use Dedicated Service Tools (DST) display.
Function 22 - Dump Main Storage
This function dumps main storage and processor data to the disk.
Note: Before to pressing function 22, determine whether function 34 is
available ( 00 shows in the panel after you select function 34). If it is
available, then the system is attempting to run a main storage dump IPL. Using
function 34 attempts to try the IPL again, such that the original dump is not
lost. If function 34 is not enabled, ( >FF shows in the panel after you select
function 34), go back and start function 22.
The first time that you select function 22 and press Enter, the system displays
attention SRC 11 A1xx 3022. This indicates that you selected function 22. To
dump main storage and system processor data to the disk, you must select
function 22 again and press Enter.
Use this function only when a main storage dump is necessary, for example,
after a suspended (system hang) condition or after an operating system failure.
Attention: No system shutdown is performed before the main storage dump. The
use of this function can cause data loss.
Functions 25 and 26 - Service Switches 1 and 2
In function 25, the service representative switch 1 is set. Function 25 is the
first step necessary to set the service function range (50 to 99).
In function 26, the service representative switch 2 is set. Function 26 is the
second step necessary to set the service function range (50 to 99).
Function 33 - Reorder SPCN Addressing
This function puts the rack addresses in the correct order to show their
position in the system power control network (SPCN). Use it when you have added
racks to or removed them from the system.
Function 34 - Retry MSD IPL
Function 34 is enabled only for main storage dump (MSD) IPLs. You can use it
when the system is hung during the MSD IPL to try the IPL again without losing
the original dump information.
Parent topic: Instructions and descriptions for control panel functions
Related reference
Stopping the system
Subject: Consulta.
Date: Thu, 17 Dec 2009 10:24:55 -0300
From: [email protected]
To: [email protected]
Amigas/os…….
Quisiera saber en que manual de AS400 u otro de una versión o sistema anterior.
Espero sepan entender lo que explico a continuación
Puedo sacar los diferentes códigos que se pueden buscar en la pantalla o visor
que tiene el AS400, para buscar alguna de las diferentes soluciones.
Por ejemplo sé que poniendo el sisema en manual con 02 B M y alternando los
códigos que buscamos y aparecen puedo ir definiendo el sistema o si sale algún
otro error.
Algunos de los códigos son el 21,22,02,66, etc y cada uno representa un tipo de
revisión en el sistema, si alguno sabe en que manual o de dónde puedo sacar
esta información lo agradecería.
Muy bueno los comentarios sobre los diferentes temas que aparecen por los mails.
Saludos a todos desde Argentina…y gracias….
Daniel
_________________________________________________________________
¿Buscás compañero de viaje para estas vacaciones? Aprovechá MSN Amor y Amistad
http://match.ar.msn.com/channel/index.aspx?trackingid=1056241____________________________________________________
© Publicaciones Help400, S.L. - Todos los
derechos reservados http://www.help400.es
----------------------------------------------------
Para darte de baja visita la siguente URL:
http://listas.combios.es/mailman/listinfo/forum.help400
