It's working, and I'm excited!
Is there some way I can find more about "ratio factor of ambiguity
validation"? I understand the basics of integer ambiguity. I'm usually
seeing 1.2, rarely above 1.8 in this field. Is that good? Bad? What
could I expect?
Danny
On 6/20/2011 3:56 AM, Tomoji Takasu wrote:
Dear Danny
In the data window of RTKNavi, I noticed the Lat/long/height of Base
is not listed with real numbers (90deg 0m). This isn't right- that
GPS has a fine solution in NMEA.
You have to set the base-station position properly in
Options dialog for relative modes. RTKNAVI never uses
receiver's NMEA.
This is FAQ. So I will add FAQ in the support page.
regards,
********
Tomoji TAKASU
--------------------------------------------------
From: "Danny Miller" <[email protected]>
Sent: Monday, June 20, 2011 5:07 PM
To: <[email protected]>
Subject: [FOSS-GPS] Can't get Ambiguity Validation Ratio to move
I'm new to RTK. I have a pair of LEA-6T GPS units, one active
Sarantel SL-1206 quadrafiliar helix ant. There were supposed to be
two of those but the second one was DOA so I'm making do with an
active patch antenna for the second. I don't have an antenna file
for either of them. I'm using 2.4.1.
I have UBX RXM-RAW and RXM-SFRB reading out of both of them at 5Hz
(tried this at 1Hz too). I can get a fix out of either one of them.
In Kinematic mode of RTKNavi, I get a position, but the "ratio factor
of ambiguity validation" factor is stuck at 0.0. I waited like an
hour and it was still at 0.
In the data window of RTKNavi, I noticed the Lat/long/height of Base
is not listed with real numbers (90deg 0m). This isn't right- that
GPS has a fine solution in NMEA. Both Base and Rover are showing
strong (~45dbHz) signal bars in all colors.
I looked under Solution 1 and Solution 2 and both have valid, similar
solutions.
I looked under errors and saw:
eight "outlier rejected" per sample period (5Hz)
one "no double-differenced residuals" message
I tried switching the COM ports for Base and Rover, effectively
switching which unit was which (neither is moving right now).
Nothing changed, the "Base" unit channel still has no Lat/long/height
and ambiguity validation is still 0. That is, the problem is not
tied to the GPS hardware unit.
I tried disabling the Rover in RTKnavi. There's still no solution
under the Lat/Long/Height of Base. The signal strength bars all turn
gray.
I tried the mkl version (I have an i7). It didn't change anything.
I tried 2.4.0 rtknavi. In that one, I can't get a rover solution to
show up at all, it's blank on the main window and rtkplot shows nothing.
Any ideas?
Danny
_______________________________________________
This message is sent to you from [email protected] mailing list.
Visit http://lists.osgeo.org/mailman/listinfo/foss-gps to manage your
subscription
For more information, check http://wiki.osgeo.org/wiki/FOSS-GPS
_______________________________________________
This message is sent to you from [email protected] mailing list.
Visit http://lists.osgeo.org/mailman/listinfo/foss-gps to manage your
subscription
For more information, check http://wiki.osgeo.org/wiki/FOSS-GPS
_______________________________________________
This message is sent to you from [email protected] mailing list.
Visit http://lists.osgeo.org/mailman/listinfo/foss-gps to manage your
subscription
For more information, check http://wiki.osgeo.org/wiki/FOSS-GPS
