Following up my previous email with an update and an additional
question...
Update: Brocade TAC has suggested a software upgrade because this
appears to be an issue with the code version we are running. That
upgrade has NOT been completed yet so I cannot confirm or deny
resolution to the issue with that solution.
Question: I noticed that this is the only XMR that is running Cisco
SFP optics. Specifically, there are two Cisco SFPs on this card that
each pass ~20Mbps. Has anyone seen linecard reboots when using 3rd
Party optics, specially Cisco optics?
Thanks for sharing any of your experiences and for any feedback or
insights.
--
Brad Fleming
On Mar 11, 2010, at 8:44 PM, Brad Fleming wrote:
We just saw this on one of our NetIron XMR 4000 devices:
Mar 11 19:03:00:N:System: Module 1 powered on
Mar 11 19:02:59:N:System: Module 1 powered off
Mar 11 19:02:59:I:System: Interface ethernet 1/20, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/19, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/16, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/12, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/11, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/10, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/6, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/5, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/2, state down -
unspecified
Mar 11 19:02:59:I:System: Interface ethernet 1/1, state down -
unspecified
Mar 11 19:02:59:N:System: Module down in slot 1, reason
CARD_DOWN_REASON_POWERED_OFF_BY_USER. Error Code 0
Mar 11 19:02:59:D:System: TM errors detected in slot 1 ppcr 0 Reg
Offset 00002080 Value 00000400
Mar 11 19:02:59:D:System: Module reset in slot 1, TM errors detected
Here's a show version output for that card:
=
=
=
=
======================================================================
SL 1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #:
<<deleted>>, Part #: 35570-200B)
Boot : Version 3.5.0fT175 Copyright (c) 1996-2007 Foundry
Networks, Inc.
Compiled on Sep 22 2008 at 11:28:04 labeled as xmlprm03500f
(387720 bytes) from boot flash
Monitor : Version 3.5.0fT175 Copyright (c) 1996-2007 Foundry
Networks, Inc.
Compiled on Oct 31 2008 at 12:06:22 labeled as xmlb03500f
(387707 bytes) from code flash
IronWare : Version 4.0.0cT177 Copyright (c) 1996-2007 Foundry
Networks, Inc.
Compiled on Apr 28 2009 at 22:01:00 labeled as xmlp04000ca
(4114050 bytes) from Primary
FPGA versions:
Valid PBIF Version = 3.14, Build Time = 12/17/2008 14:32:00
Valid XPP Version = 5.07, Build Time = 12/9/2008 16:39:00
BCM5695GMAC 0
BCM5695GMAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
PPCR0: 1024K entries CAM, 16384K PRAM, 2048K AGE RAM
LP Slot 1 uptime is 1 hours 38 minutes 24 seconds
=
=
=
=
======================================================================
Has anyone else seen behavior like this on a NI XMR before?
Thanks for any suggestions or insights.
--
Brad Fleming
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp
