Try: tag-type tag2 eth 1/1
tag2 should default to 88a8 on the CES/CER. -- Blake Covarrubias > On Dec 30, 2015, at 21:58, Daniel Hooper <[email protected]> wrote: > > Hi, > > I’m trying to setup VLL’s between a CER2000 running code version 5.9 and a > Tellabs / Coriant 8602 router. > > I can get the VLL’s up ok, what is confusing on the brocade side is raw-mode > and raw-pass-through-mode. > > Essentially on my Coriant device I am accepting SVLAN 0x88a8 tagged frames > and stripping the outer tag off before pushing them down the VLL, I’m simply > using SVLAN’s to be the service identifier on the AC interface. > > I want to be able to transparently pass inner 0x8100 tags over the VLL, it > appears though no matter what I do on the CER2000 it seems to strip the inner > tags off. > > I’ve tried raw-mode and raw-pass-through-mode on the VLL configuration, > specifying ‘untag e 1/1’ inside the VLL configuration, I’ve also tried > changing the tag value of tag2 to 9100 and configuring tag-type tag2 on port > e 1/1 (uplink to customer CPE) > > Has anyone got any idea’s on what I can try? > > If I do this same setup with coriant routers back to back it works ok as > expected. > > This is info and config I currently have on the Brocade: > > ! > router mpls > policy > traffic-eng isis level-2 > handle-isis-neighbor-down > rsvp > rsvp-hello acknowledgements > ldp > lsr-id 10.0.0.10 > mpls-interface e1/48 > ldp-enable > > vll moo 100 raw-mode > vll-peer 10.0.0.3 > untag e 1/1 > ! > ! > > Brocade-sw# show mpls vll detail > VLL moo, VC-ID 100, VLL-INDEX 1 > > End-point : untagged e 1/1 > End-Point state : Up > MCT state : None > Local VC type : untag > Local VC MTU : 9190 > COS : -- > Extended Counters: Disabled > Counter : disabled > > Vll-Peer : 10.0.0.3 > State : UP > Remote VC type : untag Remote VC MTU : 9190 > Local label : 851968 Remote label : 1286 > Local group-id : 0 Remote group-id: 5010 > Tunnel LSP : LDP (tnl2) > MCT Status TLV : Active > LSPs assigned : No LSPs assigned > > > Some further info from the Coriant: > > ! > pwe3 circuit MOO 100 mpls ldp 10.0.0.10 > ! > # Interfaces and their configuration: > interface ge0/0 > mtu 9216 > ip mtu 9190 > mpls mtu 9190 > no shutdown > qos mapping enable > ! > interface ge0/0#svlan#4000 > ip mtu 9190 > pwe3 circuit MOO encapsulation ethernet untagged > no shutdown > ! > > Router3#show ldp pwe3 detail > vcid: 100, name: MOO, type: ethernet, local groupid: 5010, remote groupid: 0 > (vc is UP) > destination: 10.0.0.10, Peer LDP Ident: 10.0.0.10 > Local label: 1286, remote label: 851968 > PSN tunnel to 10.0.0.10: present > VC QoS: none contraints: include-any 0x0 include-all 0x0 exclude-any 0x0 > Client IF: ge0/0#svlan#4000 > Local Control Word: pref 0 sent 0, Remote Control Word: rcvd 0, Result: not > used > Local PW status: supported, Remote PW status: not supported, Method used: > label-withdraw > Remote interface status: UP > Local interface status: UP > > > > Kind Regards, > > Daniel Hooper > _______________________________________________ > foundry-nsp mailing list > [email protected] > http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
