Are you sure ksymoops is available on foxboard? Does not seem logic to run it from another architecture.
a) The board Freezes after the crash, have to turn off and on after. b) I could capture the oops message on my serial console, but would be the same format as log messages? c) I tried to do some printk in keyboard.c, nothing.. i must be far away where it crashes. While compiling, i get a messgae "cannot generate rawmode keyboard for this architecture yet" when CONFIG_KEYBOARD_ATKBD is defined. I tried to UNSET KEYBOARD for the kernel and let only Virtual Keyboard, CONFIG_KEYBOARD_ATKBD is still defined, where all those CONFIG_ defines are generated? And which file? thanks --- In [email protected], "blogic79" <[EMAIL PROTECTED]> wrote: > > run ksymoops on it > > --- In [email protected], "xfingerfox32" <xfinger@> wrote: > > > > Sorry, here is the message: > > > > # IRP: c00b37f2 SRP: c00b3a76 DCCR: 00000484 USP: 00000000 MOF: > > 000000cf > > r0: c04dac80 r1: 00000045 r2: 00000001 r3: 00000001 > > r4: 00000000 r5: c048a4dc r6: 00000001 r7: c04da740 > > r8: 00000010 r9: 00000000 r10: 00000045 r11: 00000001 > > r12: 00000000 r13: 00000000 oR10: 00000045 sp: c01b3d7c > > R_MMU_CAUSE: 00001011 > > Process swapper (pid: 0, stackpage=c01946b8) > > > > Stack from c01b3c88: > > c00060ac c01b3d7c c00046b0 c0005e08 c01b3d7c 000000cf c01b3d7c > > c01946b8 > > c0167188 00000000 c01b3d7c c00047ca 00000000 00001011 00000000 > > c00055d2 > > 00000001 c048a4dc 00000000 00000010 c07fe000 00001011 00000000 > > 00000000 > > Call Trace: [<c00060ac>] [<c00046b0>] [<c0005e08>] [<c00047ca>] > > [<c00055d2>] [<c002b0f0>] [<c00098ca>] > > [<c0005be8>] [<c00b3a76>] [<c00b37f2>] [<c00b3a76>] > > [<c0104e88>] [<c00fda78>] [<c00f7fd4>] [<c00f822e>] > > [<c00f82f0>] [<c00f837a>] [<c00e5b8a>] [<c00f1aca>] > > [<c00f486e>] [<c002630c>] [<c00263e4>] [<c0004926>] > > [<c000689a>] [<c0006934>] [<c00045e8>] [<c010870e>] > > [<c00045e8>] [<c00045e8>] > > Code: 24 f7 19 c0 64 4a 5f 4d b1 00 62 2a (0e) 30 6d 66 5f 2d 72 09 > > 6d 9e 04 20 > > <0>Kernel panic - not syncing: Aiee, killing interrupt handler! > > > > > > > > --- In [email protected], "xfingerfox32" <xfinger@> wrote: > > > > > > Hi, > > > > > > After configuring the kernel for the mini-keypad any keystroke > > > generates a kernel panic. It seems (from my litle knowledge) that > > > linux axis does not yet handle keyboard. My last hope is to try to > > > force the HID interface to use the usbkbd Handler instead of kbd. > > > Have no idea how to load the usbkbd driver into the kernel, or if > > it > > > is already there, how to force usbkbd driver to claim that > > interface. > > > I have another embedded device (arm920) with kernel 2.4.25 and that > > > handles this keypad as it should, but i dont have the sources and > > the > > > kernel 2.4 is does not look similar when looking at /proc/bus. > > > > > > here is all the information in a hope that somebody could help find > > > where the offending code is? > > > > > > Cheers > > > > > > cat /proc/devices > > > Character devices: > > > 1 mem > > > 2 pty > > > 3 ttyp > > > 4 /dev/vc/0 > > > 4 tty > > > 4 ttyS > > > 4 ttyS > > > 5 /dev/tty > > > 5 /dev/console > > > 5 /dev/ptmx > > > 7 vcs > > > 10 misc > > > 13 input > > > 90 mtd > > > 108 ppp > > > 120 etrax gpio > > > 121 ds1302 > > > 123 i2c > > > 128 ptm > > > 136 pts > > > 180 usb > > > 188 ttyUSB > > > 189 usb_device > > > > > > Block devices: > > > 1 ramdisk > > > 8 sd > > > 31 mtdblock > > > 65 sd > > > 66 sd > > > 67 sd > > > 68 sd > > > 69 sd > > > 70 sd > > > 71 sd > > > 128 sd > > > 129 sd > > > 130 sd > > > 131 sd > > > 132 sd > > > 133 sd > > > 134 sd > > > 135 sd > > > > > > > > > cat devices > > > I: Bus=0003 Vendor=05a4 Product=9840 Version=0110 > > > N: Name="USB Compliant Keypad" > > > P: Phys=usb-hc-crisv10.0-1/input0 > > > S: Sysfs=/class/input/input-1 > > > H: Handlers=kbd > > > B: EV=120003 > > > B: KEY=10000 7 ff87207a c14057ff febeffdf ffefffff ffffffff > > fffffffe > > > B: LED=1f > > > > > > # cat handlers > > > N: Number=0 Name=kbd > > > > > > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > > > B: Alloc=118/900 us (13%), #Int= 1, #Iso= 0 > > > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 > > > P: Vendor=0000 ProdID=0000 Rev= 2.06 > > > S: Manufacturer=Linux 2.6.15 hc-crisv10 > > > S: Product=ETRAX 100LX USB Host Controller > > > S: SerialNumber=hc-crisv10.0 > > > C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA > > > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > > > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms > > > > > > T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 > > > D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > > > P: Vendor=05a4 ProdID=9840 Rev= 1.10 > > > S: Product=USB Compliant Keypad > > > C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 48mA > > > I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid > > > E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=13ms > > > > > >
