Hi, I am glad to hear that you and Xavier get it working, so must be something i am doing wrong.
Thanks for the information. You say stabilized 5v, and i have the foxboard alone with the BEST JOB DC power supply that give us 5.09v unloaded, cant see how i can get better than this, and for the 4 foxboard have the same error, humm.. Could you and Xavier tell exactly how you did it? Are you using FAT or FAT32 or ext2? Did you format the kingston on a windows box? Can you give the correct string to mount it? Best regards, Alexander --- In [email protected], "Michele Costantino \(KappaMic\)" <[EMAIL PROTECTED]> wrote: > > Kingstone datatravel 512mb with stabilized 5v works perfectly. > > > ________________________________ > > Da: [email protected] [mailto:[EMAIL PROTECTED] Per conto di > xfingerfox32 > Inviato: domenica 4 novembre 2007 20.06 > A: [email protected] > Oggetto: [foxboard] Re: USB memory stick problem - KINGSTON 2GB and 512 MB > > > > a bit more information: > > The foxboard is working at 4.73v loaded, so it could be that KINGSTON > is very sensitive, than i got foxboard alone with 5.09v and it took a > while to return the same error. SCSI disk error : .... return code = > 70000. Error 0x7 is Internal Error. > > Things get worst with kernel 2.6.15 for the LX832, it refuses to get > a valid address and disconnect and tells me to "check cable".. > > I have 2 classic foxboard and 2 LX832, all the same error. > > Anyone got a DataTraveler model working with foxboard? > I would apprciate any information. > > Regards, > Alexander > > --- In [email protected] <mailto:foxboard% 40yahoogroups.com> , > "xfingerfox32" <xfinger@> wrote: > > > > Hello, > > > > I have read that many of you can mount a memory stick, but i am > > unable to do so in kernel 2.4 and 2.6, default fimage or not. > > > > I am using 2 KINGSTON memory stick, 2 GB and 512 MB, and both fails. > > when i mount it "mount -t vfat /dev/sda1 /mnt1" i get the message: > > > > usb-host.c: USB controller running. > > hub.c: new USB device ETRAX 100LX-1, assigned address 2 > > scsi0 : SCSI emulation for USB Mass Storage devices > > Vendor: Kingston Model: DataTraveler 2.0 Rev: PMAP > > Type: Direct-Access ANSI SCSI revision: 02 > > Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 > > SCSI device sda: 4030464 512-byte hdwr sectors (2064 MB) > > sda: Write Protect is off > > Partition check: > > sda: sda1 sda2 sda3 sda4 > > WARNING: USB Mass Storage data integrity not assured > > USB Mass Storage device found at 2 > > usb-host.c: Got epid attn for bulk endpoint, epid 0 > > usb-host.c: Stall for epid 0 > > usb-host.c: Completing bulk urb with status -32. > > I/O error: dev 08:01, sector 0 > > FAT: unable to read boot sector > > > > I have tried FAT and FAT32, all failed and my linux box reads and > > writes fine, also my XP box. > > > > Perhaps KINGSTON works only on USB 2.0? i dont have any other maker > > to try. > > > > Have anyone get it working? > > > > If someone can mount it, or have an idea of what i am doing wrong, > > please point it out. > > > > Regards > > > > Alexander > > >
