Hi All,
I'm not able to get graphics to display in FrameMaker. This is a structured
environment I've been trying to create based on mil-std 40051 DTD. I think I do
not know how to set up the RW-Rules.
This is how a graphic is coded in the XML data:
<!ENTITY ja23-0000 SYSTEM "Graphics\ja23-0000.tiff" NDATA TIF>
...
<graphic boardno="ja23-0000"/>
DTD:
<!ELEMENT graphic (mapref*)>
<!ATTLIST graphic
%graphicatt;
hplace (left | right | center | none ) #IMPLIED
graphsty NMTOKEN #IMPLIED
applicable IDREFS #IMPLIED
%bodyatt;
>
EDD created in FM from above DTD:
Element (Container): graphic
General rule: mapref*
Attribute list
Name: boardno String Required
Name: boardfile String Optional
Name: reprowid String Optional
Name: reprodep String Optional
Name: unitmeasure Choice Optional
Choices: mm | cm | px | in | pt | pi
Default: in
Name: hscale String Optional
Name: vscale String Optional
Name: scalefit Choice Optional
Choices: yes | no
Name: alt String Optional
Name: hplace Choice Optional
Choices: left | right | center | none
Name: graphsty String Optional
Name: applicable ID References Optional
Name: inschlvl Choice Optional
Choices: 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | 31 |
32 | 33 | 34 | 35 | 36 | 37 | 38 | 39 | 40 | 41 | 42 | 43 | 44 | 45 | 46 | 47 |
48 | 49 | 50 | 51 | 52 | 53 | 54 | 55 | 56 | 57 | 58 | 59 | 60 | 61 | 62 | 63 |
64 | 65 | 66 | 67 | 68 | 69 | 70 | 71 | 72 | 73 | 74 | 75 | 76 | 77 | 78 | 79 |
80 | 81 | 82 | 83 | 84 | 85 | 86 | 87 | 88 | 89 | 90 | 91 | 92 | 93 | 94 | 95 |
96 | 97 | 98 | 99
Default: 0
Name: delchlvl Choice Optional
Choices: 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | 31 |
32 | 33 | 34 | 35 | 36 | 37 | 38 | 39 | 40 | 41 | 42 | 43 | 44 | 45 | 46 | 47 |
48 | 49 | 50 | 51 | 52 | 53 | 54 | 55 | 56 | 57 | 58 | 59 | 60 | 61 | 62 | 63 |
64 | 65 | 66 | 67 | 68 | 69 | 70 | 71 | 72 | 73 | 74 | 75 | 76 | 77 | 78 | 79 |
80 | 81 | 82 | 83 | 84 | 85 | 86 | 87 | 88 | 89 | 90 | 91 | 92 | 93 | 94 | 95 |
96 | 97 | 98 | 99
Default: 0
Name: comment String Optional
Name: changeref ID References Optional
Name: idref ID References Optional
Name: assocfig ID References Optional
Name: skilltrk String Optional
Name: security Choice Optional
Choices: uc | fouo | c | s | ts
R-W Rules:
element "graphic" {
is fm graphic element "graphic";
attribute "boardno"
{
is fm property entity;
is fm attribute;
}
}
The R-W rule above gives error:
"Type mismatch for the Framemaker element (graphic). The type defined by the
read/write rules is different from that defined by the template."
If I change the above to "is fm graphic element "Graphic";"
Then I will get an invalid Graphic element with the image in FrameMaker, and it
is much too large.
One thing I read is that a graphic should be in a "graphic" type element rather
than a container. I could not figure out how to manually create this element
with the attribute (entity?) boardno, however. Perhaps the EDD and RW Rules are
both incorrect?
Thanks for any assistance,
C2
_______________________________________________
This message is from the Framers mailing list
Send messages to [email protected]
Visit the list's homepage at http://www.frameusers.com
Archives located at http://www.mail-archive.com/framers%40lists.frameusers.com/
Subscribe and unsubscribe at
http://lists.frameusers.com/listinfo.cgi/framers-frameusers.com
Send administrative questions to [email protected]
