On 01/21/12 18:48, Alexander Motin wrote:
On 01/21/12 18:24, Dominic Fandrey wrote:
On 11/01/2012 20:33, Alexander Motin wrote:
I would like request for testing of my work on further HDA sound
driver improvement.
...
Comments and tests results are welcome!
I've been testing the first version of your patch on an HP 6510b, since
the 12th of January.
hdac0@pci0:0:27:0: class=0x040300 card=0x30c0103c chip=0x284b8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801H (ICH8 Family) HD Audio Controller'
class = multimedia
subclass = HDA
mixer
Mixer vol is currently set to 80:80
Mixer bass is currently set to 75:75
Mixer treble is currently set to 40:40
Mixer pcm is currently set to 100:100
Mixer speaker is currently set to 0:0
Mixer line is currently set to 0:0
Mixer mic is currently set to 0:0
Mixer rec is currently set to 50:50
Mixer igain is currently set to 0:0
Mixer ogain is currently set to 0:0
Mixer monitor is currently set to 0:0
Recording source: monitor
So far I haven't encountered any regressions. There are however some
small
issues that also are present with the old driver.
I have the following selection of recording devices:
Mixer line is currently set to 0:0
Mixer mic is currently set to 0:0
Mixer monitor is currently set to 0:0
To record from the microphone, I have to use the monitor device:
Recording source: monitor
monitor is a name used for the second (or built-in) microphone. List of
names in OSS is quite limited, so I had to choose one and that fit best.
Physically neither the notebook nor the docking station have a line
in socket. Of course such a thing might simply be on board and NC.
It is question to vendor, why it haven't disabled it in codec
configuration if it is not implemented in hardware. If you like, you can
do it with device hints.
Setting a volume for line, mic or monitor has no effect. To hear the
microphone on my speakers/headphones I have to use igain instead.
Difficult to say something without knowing model of codec or having
verbose dmesg output. Depending on codec model, line, mic and monitor
input may have or not have much controls. There may be just mutters, or
may be just their volume in input monitoring.
Igain sets the microphone volume independent of the recording source.
As written in man page, igain controls "input-to-output monitoring
loopback level". It is not used for pre-amplification as you may think,
because there usually more then one input that needs that control.
There's also ogain, which doesn't seem to do anything either.
ogain is used to control EAPD signal, that on some laptops used to
control external power amplifier. It is impossible for driver to find
whether this signal is used, so it is exposed always when present.
What I expect is that the recording source for the microphone was
mic and that the monitor recording source could be used to record
the cumulative output of all channels.
About mic, it is only question of terminology. What's about mixed
recording, depending on codec it may be possible in two ways: either by
recording from special device called mix, or by choosing several
recording sources with `mixer =rec mic ; mixer +rec monitor; mixer +rec
line`.
Or it may be just technically impossible.
If "record the cumulative output of all channels" means you want to
record from playback, then on most codecs it is technically impossible.
I've seen only one or two allowing it and it is not supported now.
Just now I am working on complete rewrite of the volumes control in the
driver. Terminology will remain the same, but number of present controls
and their functionality/quality should improve.
--
Alexander Motin
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
