>
>
> Can you please try this patch?
>
> http://people.freebsd.org/~jkim/amdtemp3.diff
>
> Thanks,
>
> Jung-uk Kim
>
After that patch temp appears to work, but the value seems low not sure why
Titan# sysctl dev.cpu
dev.cpu.0.%desc: ACPI CPU
dev.cpu.0.%driver: cpu
dev.cpu.0.%location: handle=\_PR_.C000
dev.cpu.0.%pnpinfo: _HID=none _UID=0
dev.cpu.0.%parent: acpi0
dev.cpu.0.temperature: 16.7C
dev.cpu.0.freq: 3300
dev.cpu.0.freq_levels: 3300/14580 3000/11615 2400/7848 1800/4860 1400/3330
dev.cpu.0.cx_supported: C1/0 C2/100
dev.cpu.0.cx_lowest: C1
dev.cpu.0.cx_usage: 100.00% 0.00% last 2229us
dev.cpu.1.%desc: ACPI CPU
dev.cpu.1.%driver: cpu
dev.cpu.1.%location: handle=\_PR_.C001
dev.cpu.1.%pnpinfo: _HID=none _UID=0
dev.cpu.1.%parent: acpi0
dev.cpu.1.temperature: 16.7C
dev.cpu.1.cx_supported: C1/0 C2/100
dev.cpu.1.cx_lowest: C1
dev.cpu.1.cx_usage: 100.00% 0.00% last 1009us
dev.cpu.2.%desc: ACPI CPU
dev.cpu.2.%driver: cpu
dev.cpu.2.%location: handle=\_PR_.C002
dev.cpu.2.%pnpinfo: _HID=none _UID=0
dev.cpu.2.%parent: acpi0
dev.cpu.2.temperature: 16.7C
dev.cpu.2.cx_supported: C1/0 C2/100
dev.cpu.2.cx_lowest: C1
dev.cpu.2.cx_usage: 100.00% 0.00% last 1603us
dev.cpu.3.%desc: ACPI CPU
dev.cpu.3.%driver: cpu
dev.cpu.3.%location: handle=\_PR_.C003
dev.cpu.3.%pnpinfo: _HID=none _UID=0
dev.cpu.3.%parent: acpi0
dev.cpu.3.temperature: 16.7C
dev.cpu.3.cx_supported: C1/0 C2/100
dev.cpu.3.cx_lowest: C1
dev.cpu.3.cx_usage: 100.00% 0.00% last 14455us
dev.cpu.4.%desc: ACPI CPU
dev.cpu.4.%driver: cpu
dev.cpu.4.%location: handle=\_PR_.C004
dev.cpu.4.%pnpinfo: _HID=none _UID=0
dev.cpu.4.%parent: acpi0
dev.cpu.4.temperature: 16.7C
dev.cpu.4.cx_supported: C1/0 C2/100
dev.cpu.4.cx_lowest: C1
dev.cpu.4.cx_usage: 100.00% 0.00% last 15621us
dev.cpu.5.%desc: ACPI CPU
dev.cpu.5.%driver: cpu
dev.cpu.5.%location: handle=\_PR_.C005
dev.cpu.5.%pnpinfo: _HID=none _UID=0
dev.cpu.5.%parent: acpi0
dev.cpu.5.temperature: 16.7C
dev.cpu.5.cx_supported: C1/0 C2/100
dev.cpu.5.cx_lowest: C1
dev.cpu.5.cx_usage: 100.00% 0.00% last 41239us
Titan#
Titan# dmesg
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #3 r232068M: Thu Feb 23 14:17:12 CST 2012
root@Titan:/usr/obj/usr/src/sys/TITAN amd64
WARNING: WITNESS option enabled, expect reduced performance.
CPU: AMD FX(tm)-6100 Six-Core Processor (3322.19-MHz K8-class
CPU)
Origin = "AuthenticAMD" Id = 0x600f12 Family = 15 Model = 1 Stepping
= 2
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x1e98220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,OSXSAVE,AVX>
AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
AMD
Features2=0x1c9bfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,NodeId,Topology,<b23>,<b24>>
TSC: P-state invariant, performance statistics
real memory = 17179869184 (16384 MB)
avail memory = 16481722368 (15718 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <GBT GBTUACPI>
FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs
FreeBSD/SMP: 1 package(s) x 6 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ctl: CAM Target Layer loaded
cryptosoft0: <software crypto> on motherboard
acpi0: <GBT GBTUACPI> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cfca0000 (3) failed
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xef00-0xef7f mem
0xf8000000-0xf9ffffff,0xd0000000-0xd7ffffff,0xdc000000-0xdfffffff irq 18 at
device 0.0 on pci1
nvidia0: <GeForce GT 545> on vgapci0
vgapci0: child nvidia0 requested pci_enable_io
vgapci0: child nvidia0 requested pci_enable_io
hdac0: <NVIDIA GT116 HDA Controller> mem 0xfbffc000-0xfbffffff irq 19 at
device 0.1 on pci1
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 9.0 on pci0
pci2: <ACPI PCI bus> on pcib2
xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfd1f8000-0xfd1fffff irq 17
at device 0.0 on pci2
xhci0: 64 byte context size.
usbus0 on xhci0
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
pci3: <ACPI PCI bus> on pcib3
atapci0: <Marvell ATA controller> port
0xcf00-0xcf07,0xce00-0xce03,0xcd00-0xcd07,0xcc00-0xcc03,0xcb00-0xcb0f mem
0xfdbff000-0xfdbff1ff irq 18 at device 0.0 on pci3
ata2: <ATA channel> at channel 0 on atapci0
ata3: <ATA channel> at channel 1 on atapci0
ahci0: <ATI IXP700 AHCI SATA controller> port
0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f mem
0xfdfff000-0xfdfff3ff irq 19 at device 17.0 on pci0
ahci0: AHCI v1.20 with 4 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ohci0: <OHCI (generic) USB controller> mem 0xfdffe000-0xfdffefff irq 18 at
device 18.0 on pci0
usbus1: <OHCI (generic) USB controller> on ohci0
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdffd000-0xfdffd0ff irq 17
at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci1: <OHCI (generic) USB controller> mem 0xfdffc000-0xfdffcfff irq 18 at
device 19.0 on pci0
usbus3: <OHCI (generic) USB controller> on ohci1
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfdffb000-0xfdffb0ff irq 17
at device 19.2 on pci0
usbus4: EHCI version 1.0
usbus4: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700/800 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci1
ata1: <ATA channel> at channel 1 on atapci1
hdac1: <ATI SB600 HDA Controller> mem 0xfdff4000-0xfdff7fff irq 16 at
device 20.2 on pci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci4: <ACPI PCI bus> on pcib4
fwohci0: <VIA Fire II (VT6306)> port 0xbf00-0xbf7f mem
0xfddff000-0xfddff7ff irq 22 at device 14.0 on pci4
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:49:e5:50:51:51:05:00
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xcfd8c000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:49:e5:51:05:00
fwe0: Ethernet address: 02:49:e5:51:05:00
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:49:e5:50:51:51:05:00 @ 0xfffe00000000, S400,
maxrec 2048
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER
mode
ohci2: <OHCI (generic) USB controller> mem 0xfdffa000-0xfdffafff irq 18 at
device 20.5 on pci0
usbus5: <OHCI (generic) USB controller> on ohci2
pcib5: <ACPI PCI-PCI bridge> at device 21.0 on pci0
pci5: <ACPI PCI bus> on pcib5
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port
0xae00-0xaeff mem 0xfd9ff000-0xfd9fffff,0xfd9f8000-0xfd9fbfff irq 17 at
device 0.0 on pci5
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 50:e5:49:bd:28:28
pcib6: <ACPI PCI-PCI bridge> at device 21.1 on pci0
pci6: <ACPI PCI bus> on pcib6
xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfd8f8000-0xfd8fffff irq 17
at device 0.0 on pci6
xhci1: 64 byte context size.
usbus6 on xhci1
pcib7: <ACPI PCI-PCI bridge> at device 21.2 on pci0
pci7: <ACPI PCI bus> on pcib7
pcib8: <ACPI PCI-PCI bridge> at device 21.3 on pci0
pci8: <ACPI PCI bus> on pcib8
ohci3: <OHCI (generic) USB controller> mem 0xfdff9000-0xfdff9fff irq 18 at
device 22.0 on pci0
usbus7: <OHCI (generic) USB controller> on ohci3
ehci2: <EHCI (generic) USB 2.0 controller> mem 0xfdff8000-0xfdff80ff irq 17
at device 22.2 on pci0
usbus8: EHCI version 1.0
usbus8: <EHCI (generic) USB 2.0 controller> on ehci2
amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcd7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
firewire0: bus manager 0
ZFS filesystem version 5
ZFS storage pool version 28
Timecounters tick every 1.000 msec
vboxdrv: fAsync=0 offMin=0x6e9 offMax=0x8c5
hdacc0: <NVIDIA (0x0015) HDA CODEC> at cad 0 on hdac0
hdaa0: <NVIDIA (0x0015) HDA CODEC Audio Function Group> at nid 1 on hdacc0
pcm0: <NVIDIA (0x0015) HDA CODEC PCM (HDMI/DP 8ch)> at nid 5 on hdaa0
hdacc1: <NVIDIA (0x0015) HDA CODEC> at cad 1 on hdac0
hdaa1: <NVIDIA (0x0015) HDA CODEC Audio Function Group> at nid 1 on hdacc1
pcm1: <NVIDIA (0x0015) HDA CODEC PCM (HDMI/DP 8ch)> at nid 5 on hdaa1
hdacc2: <NVIDIA (0x0015) HDA CODEC> at cad 2 on hdac0
hdaa2: <NVIDIA (0x0015) HDA CODEC Audio Function Group> at nid 1 on hdacc2
pcm2: <NVIDIA (0x0015) HDA CODEC PCM (HDMI/DP 8ch)> at nid 5 on hdaa2
hdacc3: <NVIDIA (0x0015) HDA CODEC> at cad 3 on hdac0
hdaa3: <NVIDIA (0x0015) HDA CODEC Audio Function Group> at nid 1 on hdacc3
pcm3: <NVIDIA (0x0015) HDA CODEC PCM (HDMI/DP 8ch)> at nid 5 on hdaa3
hdacc4: <Realtek ALC889 HDA CODEC> at cad 0 on hdac1
hdaa4: <Realtek ALC889 HDA CODEC Audio Function Group> at nid 1 on hdacc4
pcm4: <Realtek ALC889 HDA CODEC PCM (Rear Analog 7.1/2.0)> at nid
20,22,21,23 and 24,26 on hdaa4
pcm5: <Realtek ALC889 HDA CODEC PCM (Front Analog)> at nid 27 and 25 on
hdaa4
pcm6: <Realtek ALC889 HDA CODEC PCM (Rear Digital)> at nid 30 on hdaa4
pcm7: <Realtek ALC889 HDA CODEC PCM (Onboard Digital)> at nid 17 on hdaa4
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 5.0Gbps Super Speed USB v3.0
usbus7: 12Mbps Full Speed USB v1.0
usbus8: 480Mbps High Speed USB v2.0
ugen0.1: <0x1b6f> at usbus0
uhub0: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <0x1b6f> at usbus6
uhub6: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus6
ugen7.1: <ATI> at usbus7
uhub7: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus7
ugen8.1: <ATI> at usbus8
uhub8: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus8
uhub5: 2 ports with 2 removable, self powered
uhub7: 4 ports with 4 removable, self powered
uhub1: 5 ports with 5 removable, self powered
uhub3: 5 ports with 5 removable, self powered
uhub0: 4 ports with 4 removable, self powered
uhub6: 4 ports with 4 removable, self powered
uhub8: 4 ports with 4 removable, self powered
uhub2: 5 ports with 5 removable, self powered
uhub4: 5 ports with 5 removable, self powered
ugen3.2: <Logitech> at usbus3
ugen1.2: <Logitech> at usbus1
ums0: <Logitech USB-PS2 Optical Mouse, class 0/0, rev 2.00/21.00, addr 2>
on usbus1
ukbd1: <USB Keyboard> on usbus3
ums0: 8 buttons and [XYZ] coordinates ID=0
kbd2 at ukbd1
uhid0: <USB Keyboard> on usbus3
ada0 at ahcich1 bus 0 scbus3 target 0 lun 0
ada0: <ST3250820AS 3.AAD> ATA-7 SATA 2.x device
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad10
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #4 Launched!
Timecounter "TSC-low" frequency 12977308 Hz quality 1000
WARNING: WITNESS option enabled, expect reduced performance.
cd0 at ahcich0 bus 0 scbus2 target 0 lun 0
cd0: <Optiarc DVD RW AD-7190S 1.01> Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO 8192bytes)
cd0: cd present [120625 x 2048 byte records]
--
Sam Fourman Jr.
Fourman Networks
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
