On 09/12/15 13:45, Mark R V Murray wrote:
> 
>> On 8 Sep 2015, at 19:02, Mark R V Murray <ma...@freebsd.org> wrote:
>>
>>
>>> On 8 Sep 2015, at 17:22, Sean Bruno <sbr...@freebsd.org> wrote:
>>>
>>>
>>>>>>
>>>>>> I’m also seeing breakage with the em0 device; this isn’t a kernel
>>>>>> hang, it is a failure to move data after about 10-15 minutes. The
>>>>>> symptom is that my WAN ethernet no longer moves traffic, no pings,
>>>>>> nothing. Booting looks normal:
>>>>>>
>>>>>> em0: <Intel(R) PRO/1000 Network Connection 7.4.2> port
>>>>>> 0x30c0-0x30df mem 0x50300000-0x5031ffff,0x50324000-0x50324fff irq
>>>>>> 20 at device 25.0 on pci0 em0: Using an MSI interrupt em0: Ethernet
>>>>>> address: 00:16:76:d3:e1:5b em0: netmap queues/slots: TX 1/1024, RX
>>>>>> 1/1024
>>>>>>
>>>>>> Fixing it is as easy as …
>>>>>>
>>>>>> # ifconfig em0 down ; service ipfw restart ; ifconfig em0 up
>>>>>>
>>>>>> :-)
>>>>>>
>>>>>> I’m running CURRENT, r287538. This last worked of me a month or so
>>>>>> ago at my previous build.
>>>>>>
>>>>>> M
>>>>>>
>>>>>
>>>>>
>>>>> Just so I'm clear, the original problem reported was a failure to
>>>>> attach (you were among several folks reporting breakage).  Is that fixed
>>>>> ?
>>>>
>>>> I did not report the failure to attach, and I am not seeing it as I don’t
>>>> think I built a kernel that had that particular failure. I am having the
>>>> “failure after 10-15 minutes” problem; this is on an em0 device.
>>>>
>>>> M
>>>>
>>>
>>>
>>> Hrm, that's odd.  That sounds like a hole where interrupts aren't being
>>> reset for "reasons" that I cannot fathom.
>>>
>>> What hardware (pciconf -lv) does your system actually have?  The em(4)
>>> driver doesn't identify components which is frustrating.
>>
>> pciconf -lv output below:
>>
>> hostb0@pci0:0:0:0:   class=0x060000 card=0x514d8086 chip=0x29a08086 rev=0x02 
>> hdr=0x00
>>    vendor     = 'Intel Corporation'
>>    device     = '82P965/G965 Memory Controller Hub'
>>    class      = bridge
>>    subclass   = HOST-PCI
> 
> I just caught this, on today’s build:
> 
> em0: Watchdog timeout Queue[0]-- resetting
> Interface is RUNNING and ACTIVE
> em0: TX Queue 0 ------
> em0: hw tdh = 127, hw tdt = 139
> em0: Tx Queue Status = -2147483648
> em0: TX descriptors avail = 1012
> em0: Tx Descriptors avail failure = 0
> em0: RX Queue 0 ------
> em0: hw rdh = 0, hw rdt = 1023
> em0: RX discarded packets = 0
> em0: RX Next to Check = 0
> em0: RX Next to Refresh = 1023
> 
> [graveyard] /usr/ports 09:42 pm # uname -a
> FreeBSD graveyard.grondar.org 11.0-CURRENT FreeBSD 11.0-CURRENT #0 r287705: 
> Sat Sep 12 15:07:54 BST 2015     
> r...@graveyard.grondar.org:/b/obj/usr/src/sys/G_AMD64_GATE  amd64
> 
> M
> 

Any chance you can turn TSO off if its on and see what your results are?

sean
_______________________________________________
freebsd-current@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"

Reply via email to