On Monday 23 May 2016 15:25:39 Kenneth D. Merry wrote: > On Sat, May 21, 2016 at 09:30:35 +0300, Oleg V. Nauman wrote: > > I have faced the issue with fresh CURRENT stopped to boot on my old > > desktop > > > > after update to r300299 > > Verbose boot shows the endless cycle of > > > > ata2: SATA reset: ports status=0x05 > > ata2: reset tp1 mask=03 ostat0=50 ostat1=50 > > ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 > > ata2: stat1=0x50 err=0x01 lsb=0x00 msb=0x00 > > ata2: reset tp2 stat0=50 stat1=50 devices=0x3 > > messages logged to console. > > > > Below is the relevant portion of ATA controller/devices probed/attached > > during the boot: > > > > atapci0: <Intel ICH7 UDMA100 controller> port > > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0 > > ata0: <ATA channel> at channel 0 on atapci0 > > atapci1: <Intel ICH7 SATA300 controller> port 0xd080-0xd087, > > 0xd000-0xd003, > > 0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc80f irq 19 at device 31.2 on pci0 > > ata2: <ATA channel> at channel 0 on atapci1 > > ata3: <ATA channel> at channel 1 on atapci1 > > ada0 at ata2 bus 0 scbus1 target 0 lun 0 > > ada0: <SAMSUNG HD200HJ KF100-06> ATA-7 SATA 2.x device > > ada1 at ata2 bus 0 scbus1 target 1 lun 0 > > ada1: <ST500DM002-1BC142 JC4B> ATA8-ACS SATA 3.x device > > cd0 at ata0 bus 0 scbus0 target 0 lun 0 > > cd0: <_NEC DVD_RW ND-3570A 1.11> Removable CD-ROM SCSI device > > I'm not entirely sure what is causing the problem with your system, but > hopefully we can narrow it down a bit. > > There is a bug that came in with my SMR changes in revision 300207 that > broke the quirk functionality in the ada(4) driver. I don't think that is > the problem you're seeing, though. > > Can you try out this patch: > > https://people.freebsd.org/~ken/cam_smr_ada_patch.20160523.1.txt > > In /boot/loader.conf, put the following: > > kern.cam.ada.0.quirks="0x04" > kern.cam.ada.1.quirks="0x04" > > If you're able to boot with those quirk entries in the loader.conf, try > taking one of them out, and reboot. If that works, try taking the other > one out and reboot. > > What I'm trying to figure out here is where the problem lies: > > 1. The bug with the ada(4) driver (in where it loaded the quirks). > 2. The extra probe steps in the ada(4) driver might be causing a problem > with ada0 (Samsung drive). > 3. The extra probe steps in the ada(4) driver might be causing a problem > with ada1 (Seagate drive). > 4. Something else. > > So, if you can try the patch and try to eliminate a few possibilities, we > may be able to narrow it down.
I was able to boot after applying the patch ; kern.cam.ada.0.quirks="0x04" was the quirk in effect. It is quirk for my Samsung HD200HJ KF100-06 hard drive. > > Thanks, Thanks to you. > > Ken _______________________________________________ email@example.com mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"