On Mon, 14 Aug 2000, Brian O'Shea wrote:

> > How can i examine this situation more detailed? Can anybody help?
> Are you certain that the kernel is hanging and not just the graphics
> display?  Can you try logging in remotely over the network, or possibly
> on a serial port?
I switched to the first virtual console and run top. It freezes too.

> Also, please include :
> - A description of the hardware you are using
dmesg output in the attachment, ok?

> - When you last updated -current sources
3-4 days ago.
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #1: Sat Aug 12 12:40:47 MSD 2000
    [EMAIL PROTECTED]:/var/ftp/pub/FreeBSD/current-src/sys/compile/WS_ILMAR
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (367.50-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x660  Stepping = 0

real memory  = 134152192 (131008K bytes)
avail memory = 126640128 (123672K bytes)
Preloaded elf kernel "kernel" at 0xc03e4000.
seq0-63: Midi sequencers.
Pentium Pro MTRR support enabled
md0: Malloc disk
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82443BX (440 BX) host to PCI bridge> at 0.0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11
intpm0: <Intel 82371AB Power management controller> port 0x5000-0x500f irq 9 at device 
7.3 on pci0
intpm0: I/O mapped 5000
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 4000 
pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 9.0 irq 9
rl0: <RealTek 8139 10/100BaseTX> port 0xe400-0xe47f mem 0xe7000000-0xe700007f irq 11 
at device 11.0 on pci0
rl0: Ethernet address: 00:c0:df:23:60:e2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sbc0: <ESS ES1868> at port 0x220-0x22f,0x388-0x38b,0x330-0x331 irq 5 drq 1,0 on isa0
pcm0: <ESS 18xx DSP> on sbc0
midi0: <SB Midi Interface> on sbc0
midi1: <SB OPL FM Synthesizer> on sbc0
unknown: <PNP0303> can't assign resources
unknown: <PNP0a03> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0400> can't assign resources
unknown: <PNP0501> can't assign resources
IPsec: Initialized Security Association Processing.
ad0: 3077MB <ST33232A> [6253/16/63] at ata0-master using UDMA33
ata1-master: DMA limited to UDMA33, non-ATA66 compliant cable
ad2: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata1-master using UDMA33
acd0: CDROM <HITACHI CDR-8335> at ata1-slave using WDMA2
Mounting root from ufs:/dev/ad0s2a

Reply via email to