I installed FreeBSD 5.0-current on my notebook, because in FreeBSD4.6 
the sounddriver let the kernel hang on boot.

I know, that acpi is under developement, but here are my results testing 
acpi on this hardware.

acpiconf -s 3:
works, but the machine doesen't completely wake up, the display still 
stays dark

acpiconf -s 4:
the system hangs uo.

Here's my acpidump
RSD PTR: Checksum=17, OEMID=PTLTD, RsdtAddress=0x0fef9a90
RSDT: Length=48, Revision=1, Checksum=247,
        OEMID=SONY, OEM Table ID=K5, OEM Revision=0x6040000,
        Creator ID= LTP, Creator Revision=0x0
        Entries={ 0x0fefee4c, 0x0fefeec0, 0x0fefeee8 }
        SMI_CMD=0x802f, ACPI_ENABLE=0xf0, ACPI_DISABLE=0xf1, S4BIOS_REQ=0xf2
        P_LVL2_LAT=90ms, P_LVL3_LAT=1100ms
        DAY_ALRM=125, MON_ALRM=126, CENTURY=50

and here's my dmesg output:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #1: Fri Jul 12 11:53:31 CEST 2002
     [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc05d0000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05d00a8.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 1100048152 Hz
CPU: mobile AMD Duron(tm) (1100.05-MHz 686-class CPU)
   Origin = "AuthenticAMD"  Id = 0x662  Stepping = 2
   AMD Features=0xffffffffc0400000<AMIE,DSP,3DNow!>
real memory  = 268435456 (262144K bytes)
avail memory = 254119936 (248164K bytes)
Pentium Pro MTRR support enabled
Using $PIR table, 6 entries at 0xc00fdf60
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY   K5      > on motherboard
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe"  frequency 3579545 Hz
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <PCI bus> on acpi_pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0x1c40-0x1c4f at device 7.1 
on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x1c00-0x1c1f irq 9 at device 
7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
uhub0: port error, restarting port 2
uhub0: port error, giving up port 2
ums0: Logitech USB Mouse, rev 1.10/6.10, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci1: <VIA 83C572 USB controller> port 0x1c20-0x1c3f irq 9 at device 
7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
uhub1: port error, restarting port 2
uhub1: port error, giving up port 2
isab1: <PCI-ISA bridge> at device 7.4 on pci0
pci0: <multimedia, audio> at device 7.5 (no driver attached)
pci0: <simple comms> at device 7.6 (no driver attached)
pccbb0: <TI1420 PCI-CardBus Bridge> irq 9 at device 10.0 on pci0
cardbus0: <CardBus bus> on pccbb0
pccard0: <16-bit PCCard bus> on pccbb0
pccbb1: <TI1420 PCI-CardBus Bridge> irq 10 at device 10.1 on pci0
cardbus1: <CardBus bus> on pccbb1
pccard1: <16-bit PCCard bus> on pccbb1
pci0: <serial bus, FireWire> at device 14.0 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0x1800-0x18ff mem 
0xe8004800-0xe80048ff irq 10 at device 16.0 on pci0
rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect 
/usr/src/sys/vm/uma_core.c:1332: could sleep with "rl0" locked from 
rl0: Ethernet address: 08:00:46:5a:c4:4b
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
/usr/src/sys/vm/uma_core.c:1332: could sleep with "rl0" locked from 
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
orm0: <Option ROMs> at iomem 
0xdc000-0xdffff,0xd0000-0xd3fff,0xc0000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: CPU throttling enabled, 16 steps from 100% to 6.2%
system power profile changed to 'economy'
     ACPI-0433: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
     ACPI-0433: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
system power profile changed to 'performance'
ad0: 19077MB <HITACHI_DK23DA-20> [38760/16/63] at ata0-master UDMA100
acd0: DVD-ROM <QSI DVD-ROM SDR-081> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s2a
WARNING: / was not properly dismounted
/usr/src/sys/vm/uma_core.c:1332: could sleep with "kernel linker" locked 
from /usr/src/sys/kern/kern_linker.c:1797
/usr/src/sys/vm/uma_core.c:1332: could sleep with "kernel linker" locked 
from /usr/src/sys/kern/kern_linker.c:1797
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted
logo_saver: the console does not support M_VGA_CG320
module_register_init: MOD_LOAD (logo_saver, 0xc27bfc50, 0) error 19

JAWA Management Software GmbH
Liebenauer Hauptstr. 200
A-8041 GRAZ
Tel: ++43-(0)316-403274-12
Fax: ++43-(0)316-403274-10
GSM: ++43-(0)676-93 96 698
homepage: http://www.jawa.at
--------- privat -----------
homepage: http://www.inode.at/mbretter

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message

Reply via email to