I've recently been trying to bring a system of mine (4.7-R) up-to-date
with -CURRENT by following the dotted lines in UPDATING; basically,
everything up through 'make installkernel' and the 'make install' from
/usr/src/sys/boot has gone fine; I reboot into loader(8) and 'boot -s',
but literally just after printing its "I just loaded acpi.ko" message the
system just hangs at a twiddle-prompt, forever stilled. Well, not quite:
the keyboard lights blink once and the hard drives click, but no further
response. This isn't an ACPI problem; I've unset acpi_load, and the only
difference is that the system spins for half a second longer before dying.
loader claims to have preloaded the (new) kernel already.
Here's the dmesg from 4.7's kernel.GENERIC:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RELEASE #0: Wed Oct 9 15:08:34 GMT 2002
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (400.91-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x80000800<SYSCALL,3DNow!>
real memory = 268369920 (262080K bytes)
avail memory = 255954944 (249956K bytes)
Preloaded elf kernel "/kernel.GENERIC" at 0xc050f000.
K6-family MTRR support enabled (2 registers)
md0: Malloc disk
Using $PIR table, 5 entries at 0xc00fdcd0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <NVidia Riva TNT graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C586 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C586 ATA33 controller> port 0xd000-0xd00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 10 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x1106, dev=0x3040) at 7.3
pci0: <unknown card> (vendor=0x1102, dev=0x0002) at 8.0 irq 11
pci0: <unknown card> (vendor=0x1102, dev=0x7002) at 8.1
rl0: <RealTek 8139 10/100BaseTX> port 0xe000-0xe0ff mem 0xd7018000-0xd70180ff irq 5 at
device 9.0 on pci0
rl0: Ethernet address: 00:a0:4c:39:10:cc
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0x12b9, dev=0x1006) at 10.0 irq 9
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 16124MB <IBM-DTTA-351680> [32760/16/63] at ata0-master UDMA33
ad1: 29196MB <SAMSUNG SV3064D> [59320/16/63] at ata0-slave UDMA33
acd0: DVD-ROM <Pioneer DVD-ROM ATAPIModel DVD-103S 0115> at ata1-master PIO4
Mounting root from ufs:/dev/ad1s3a
*** end-of-file ***
...and here's the kernel configuration which isn't working, with
commented module-lines removed for your viewing convenience:
# SMYRNO -- Standard kernel configuration for smyrno.tiercel.net
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.371 2002/12/28 06:22:17 scottl Exp $
machine i386
#cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident SMYRNO
maxusers 0
#To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" #Default places to look for devices.
makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options SOFTUPDATES #Enable FFS soft updates support
options UFS_ACL #Support for access control lists
options UFS_DIRHASH #Improve performance on big directories
options MD_ROOT #MD is a potential root device
#options NFSCLIENT #Network Filesystem Client
#options NFSSERVER #Network Filesystem Server
#options NFS_ROOT #NFS usable as root device, requires NFSCLIENT
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options PROCFS #Process filesystem (requires PSEUDOFS)
options PSEUDOFS #Pseudo-filesystem framework
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 #Compatible with FreeBSD4
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
# Debugging for use in -current
options DDB #Enable the kernel debugger
#options INVARIANTS #Enable calls of extra sanity checking
#options INVARIANT_SUPPORT #Extra sanity checks of internal structures,
required by INVARIANTS
#options WITNESS #Enable checks to detect deadlocks and cycles
#options WITNESS_SKIPSPIN #Don't run witness on spinlocks for speed
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
device eisa
device pci
# Floppy drives
device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
device speaker
#hint.speaker.0.at="isa"
#hint.speaker.0.port="0x61"
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device vga # VGA video card driver
#options VESA
device splash # Splash screen and screen saver support
# syscons is the default console driver, resembling an SCO console
#device sc
# Enable this for the pcvt (VT220 compatible) console driver
device vt
options PCVT_NSCREENS=8
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx
# Power management support (see NOTES for more options)
device apm
# Add suspend/resume support for the i8254.
device pmtimer
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
#device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs that use the common MII bus controller code.
device miibus # MII bus support
device rl # RealTek 8129/8139
# Pseudo devices - the number indicates how many units to allocate.device
random # Entropy device
device loop # Network loopback
device ether # Ethernet support
#device sl # Kernel SLIP
device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
device gif # IPv6 and IPv4 tunneling
device faith # IPv6-to-IPv4 relaying (translation)
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device bpf # Berkeley packet filter
device pcm
*** end-of-file ***
Thanks in advance for any suggestions you might have.
John.
--
évana roì, séana coì, reìja venacoì u vëja haman.
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
