Hi, which driver have you converted? Did you use the Windows XP driver from the supplied CD? I had had problems with all drivers except the Windows XP driver. I run FreeBSD 6.0-RELEASE and did noticed any problem with unstable connection. I think the unstable connection may have following reason: You did not used the Windows XP driver for the conversion
As for the connection speed I suggest you to check this: a) Configuration of the pf. Checker whether traffic shapping at your pf configuration is enabled. b)Check the configuration of your AP If it is possible I will suggest you to try the WLAN connection under Windows in order to determine that your hardware (card + AP) works correctly. If it works ok, I will suggest you to disable the firewall and try to establish a connection without the firewall. Regards, Roman Am Donnerstag, den 05.01.2006, 01:05 -0200 schrieb Luís Cargnini: > i forget i use pf firewall i trie with it and worked a little bit i > must mantain the firewall or remove it. > On 05/01/06, Luís Cargnini <[EMAIL PROTECTED]> wrote: > > ok did this all but link seems unstable and i dont get much speed > > above 7~12k betwen ap and pc, how could i improve this one. Second > > system seems to have "weeping" "ic ic ic " my mouse and my system make > > some pauses, my processor achieve at least 17% of processing in idle > > mode, how to fix this things ? > > and my link crash sometimes. > > > > On 01/01/06, Roman Dewald <[EMAIL PROTECTED]> wrote: > > > > > > > Hi i have an Dlink DWL-G520+ as following: > > > > [EMAIL PROTECTED]:9:0: class=0x028000 card=0x3b041186 chip=0x9066104c > > > > rev=0x00 hdr=0x00 > > > > vendor = 'Texas Instruments (TI)' > > > > device = 'TNETW1130(ACX111) 802.11b/g Wireless Cardbus/PCI > > > > Adapter' > > > > class = network > > > > but it isn't working well, someone knows if exist an native driver or > > > > how i must proceed (walktrhough) to put this net device to work > > > I have had problems with this card and ndis driver under 5.4 Release. I > > > upgraded my system to the 6.0 Release and it worked fine. > > > > > > To get the driver working, you have first to bild a module for the > > > FreeBSD kernel from Windows drivers supplied with your card. > > > I used ndisgen to convert the driver. You will get some files after the > > > conversion you will a couple of files. > > > Then you can load the converted module with kldload +absolute path to > > > the converted module. You can check dmesg to ensure the module was > > > loaded successfully. You will see something like that: > > > > > > ndis0: <D-Link AirPlus G+ DWL-G520+ Wireless PCI Adapter> mem > > > 0xcfffa000-0xcfffbfff,0xcffc0000-0xcffdffff irq 19 at device 11.0 on > > > pci0 > > > > > > Afterwards you have to load the wlan_wep module to get the wep > > > encryption working. > > > Now you can configure the network settings with ifconfig. > > > > > > Roman > > > > > > > > > > Thanks && Regards > > > > Msc. Bsc. Luís Vitório Cargnini > > > > IEEE Member > > > > Mastering Degree student @ PUC-RS Electrical Engineer Faculty > > > > _______________________________________________ > > > > [email protected] mailing list > > > > http://lists.freebsd.org/mailman/listinfo/freebsd-hardware > > > > To unsubscribe, send any mail to "[EMAIL PROTECTED]" > > > > > > > > > > > > > > > > -- > > Thanks && Regards > > Msc. Bsc. Luís Vitório Cargnini > > IEEE Member > > Mastering Degree student @ PUC-RS Electrical Engineer Faculty > > > > > -- > Thanks && Regards > Msc. Bsc. Luís Vitório Cargnini > IEEE Member > Mastering Degree student @ PUC-RS Electrical Engineer Faculty > _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-hardware To unsubscribe, send any mail to "[EMAIL PROTECTED]"
