Hi,
I've been trying to get an alcatel speedtouch usb modem working and after
spending all afternoon struggling with it I've concluded that I don't have
USB working at all :(
I also have a xerox docuprint p8ex printer which I am using to test whether
usb is working - although I'm not concerned with making this print.
Here are my details:
I'm running FreeBSD 4.6-STABLE, I've got a dual P2-350 with a Gigabyte
GA6BXD motherboard.
The onboard USB ports are identified as "Intel 82371AB/EB (PIIX4) USB
controller".
I've updated the motherboard's bios to the latest version (F4b).
I removed a network card that was sharing an irq with the usb device so
their are definitely no irq conflicts.
A complete dmesg output is included at the end of the message along with the
output from usbd -dvvv
If I boot the machine with the usb devices attached they are recognised:
ugen0: ALCATEL Speed Touch USB , rev 1.10/0.00, addr 2
ugen1: Lexmark International, Inc. Color Jetprinter 5500\^H?\^H, rev
1.00/0.63, addr 3
But any attempt to use the adsl modem will cause the following error:
grody# modem_run -f /usr/local/libdata/mgmt.o -m -d /dev/ugen0 -v 2
Gotcha, I found your ADSL ALCATEL SpeedTouch USB modem!
(The modem lights will then start flashing for a while, then go red, then
switch off)
ugen0: at uhub0 port 1 (addr 2) disconnected
ugen0: detached
BLOCK1: Input/output error
Uploading /usr/local/libdata/mgmt.o failed! Continuing anyway ...
pusb_set_configuration 1: Inappropriate ioctl for device
I originally thought it was just problems getting the alcatel driver going
but the following happens when I try to plug either the printer or adsl
modem into the machine while it is already running:
uhub0: device problem, disabling port 1
Does anyone have any ideas? I'm completely lost. I thought being a regular
(and a bit old) intel chipset the usb would be pretty generic. After a _lot_
of searching through google and ml archives i'm thinking it might be a
problem with gigabyte boards - I saw a lot of (unanswered) messages with
similar problems from people with gigabyte boards.
Thanks
Jason.
The following is the output from running usbd -dvvv:
grody# /usr/sbin/usbd -dvvv
usbd: opened /dev/usb0
usbd: reading configuration file /etc/usbd.conf
usbd: action 1: ActiveWire board, firmware download
vndr=0x0854 prdct=0x0100 rlse=0x0000
attach='/usr/local/bin/ezdownload -f
/usr/local/share/usb/firmware/0854.0100.0_01.hex ${DEVNAME}'
usbd: action 2: Entrega Serial with UART
vndr=0x1645 prdct=0x8001 rlse=0x0101
attach='/usr/sbin/ezdownload -v -f /usr/share/usb/firmware/1645.8001.0101
/dev/${DEVNAME}'
usbd: action 3: USB ethernet
devname: [ack]ue[0-9]+
attach='dhclient ${DEVNAME}'
detach='killall dhclient'
usbd: action 4: Mouse
devname: ums[0-9]+
attach='/usr/sbin/moused -p /dev/${DEVNAME} -I
/var/run/moused.${DEVNAME}.pid'
usbd: action 5: USB device
usbd: 5 actions
usbd: opened /dev/usb
usbd: detach event at 1027071605.407825000, product 0x3201, vendor 0x0419:
vndr=0x0419 prdct=0x3201 rlse=0x0063 clss=0x0000 subclss=0x0000
prtcl=0x0000
device names: ugen1
usbd: Found action 'USB device' for product 0x3201, vendor 0x0419 at ugen1
usbd: action 0: USB device
usbd: Setting DEVNAME='ugen1'
(The following messages repeat indefinitely pausing for a while on the doing
discovery bit)
usbd: doing timeout discovery on /dev/usb0
usbd: processing event queue due to timeout on /dev/usb
usbd: doing discovery on /dev/usb0
usbd: doing timeout discovery on /dev/usb0
usbd: processing event queue due to timeout on /dev/usb
(and so on....)
dmesg output:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-STABLE #3: Thu Jul 18 19:06:38 EST 2002
jason@grody:/usr/obj/usr/src/sys/GRODY
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (349.07-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x652 Stepping = 2
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
CM
OV,PAT,PSE36,MMX,FXSR>
real memory = 402587648 (393152K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0311000.
Pentium Pro MTRR support enabled
Using $PIR table, 7 entries at 0xc00fddf0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 18 -> irq 16
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xe000-0xe01f irq 11
at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at
device 7.3 on pci0
pci0: <NVidia/SGS-Thomson Riva128 graphics accelerator> at 8.0 irq 2
sym0: <875> port 0xe400-0xe4ff mem
0xe1101000-0xe1101fff,0xe1102000-0xe11020ff irq 16 at device 10.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCAN AT BOOT disabled for targets 3 4 6 8 9 10 11 12 13 14 15.
sym0: SCAN FOR LUNS disabled for targets 0 1 2 4 5 6.
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xe800-0xe83f mem
0xe1000000-0xe10fffff,0xe1100000-0xe1100fff irq 2 at device 12.0 on pci0
fxp0: Ethernet address 00:02:b3:0b:19:61
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 12971MB <WDC WD136AA> [26354/16/63] at ata0-master UDMA33
Waiting 10 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
Mounting root from ufs:/dev/da0s1a
cd0 at sym0 bus 0 target 1 lun 0
cd0: <MATSHITA CD-ROM CR-508 XS03> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at sym0 bus 0 target 0 lun 0
da0: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da0: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
IP Filter: v3.4.27 initialized. Default = pass all, Logging = enabled
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-questions" in the body of the message
