I'm setting up a new server on 6.0 I've been planning for a long time and I am very disappointed with two critical issues. My motherboard is the ASUS K8V-X SE that I chose because it was listed as compatible at the FreeBSD/amd64 Project:
http://www.freebsd.org/platforms/amd64/motherboards.html I wonder if going back to 5.4 might help? Onto the problems... 1. I have 4 IDE drives: primary controller: Maxtor 40 GB hd (master) and LG cdrom (slave) secondary controller: Seagate Barracuda 200 GB hd (master) and Seagate Barracuda 300 GB (slave) Problem: The 300 GB drive is unusable. I set it up ok with sysinstall during the installation but the system will not boot properly if it has an entry in /etc/fstab. I get many errors like: "ad3: WARNING - READ_DMA UDMA ICRC error (retrying request) LBA=63" I also get input/output error if I try to examine its label with disklabel. dmesg output is at the end of this post when I booted without fstab line. The strange thing is that the two drives on the secondary controller are so similar. Same manufacturer, same product line, the speeds are the same. Everything is the same except the size. I ran dos-level diagnostics on it and no problems were found. 2. I can't use my USB ports! I get a line like this for each of my ports: uhci0: <VIA 83C572 USB controller> port 0xb800-0xb81f irq 21 at device 16.0 on pci0 uhci0: [GIANT-LOCKED] Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC ACPI APIC Table: <A M I OEMAPIC > Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD Athlon(tm) 64 Processor 3000+ (2002.58-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0xf4a Stepping = 10 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow> real memory = 536543232 (511 MB) avail memory = 515702784 (491 MB) MADT: Forcing active-low polarity and level trigger for SCI ioapic0 <Version 0.3> irqs 0-23 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <A M I OEMRSDT> on motherboard acpi0: Power Button (fixed) pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0 pci_link1: <ACPI PCI Link LNKB> irq 10 on acpi0 pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0 pci_link3: <ACPI PCI Link LNKD> irq 0 on acpi0 pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0 pci_link5: <ACPI PCI Link LNKF> irq 0 on acpi0 pci_link6: <ACPI PCI Link LNKG> irq 0 on acpi0 pci_link7: <ACPI PCI Link LNKH> irq 0 on acpi0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <VIA K8T800Pro host to PCI bridge> mem 0xf4000000-0xf7ffffff at device 0.0 on pci0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci0: <display, VGA> at device 11.0 (no driver attached) atapci0: <VIA 6420 SATA150 controller> port 0xe800-0xe807,0xe400-0xe403,0xe000-0xe007,0xd800-0xd803,0xd400-0xd40f,0xd000-0xd0ff irq 20 at device 15.0 on pci0 ata2: <ATA channel 0> on atapci0 ata3: <ATA channel 1> on atapci0 atapci1: <VIA 8237 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 15.1 on pci0 ata0: <ATA channel 0> on atapci1 ata1: <ATA channel 1> on atapci1 uhci0: <VIA 83C572 USB controller> port 0xb800-0xb81f irq 21 at device 16.0 on pci0 uhci0: [GIANT-LOCKED] usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 21 at device 16.1 on pci0 uhci1: [GIANT-LOCKED] usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 21 at device 16.2 on pci0 uhci2: [GIANT-LOCKED] usb2: <VIA 83C572 USB controller> on uhci2 usb2: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: <VIA 83C572 USB controller> port 0xc800-0xc81f irq 21 at device 16.3 on pci0 uhci3: [GIANT-LOCKED] usb3: <VIA 83C572 USB controller> on uhci3 usb3: USB revision 1.0 uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0: <VIA VT6202 USB 2.0 controller> mem 0xfbc00000-0xfbc000ff irq 21 at device 16.4 on pci0 ehci0: [GIANT-LOCKED] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <VIA VT6202 USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered isab0: <PCI-ISA bridge> at device 17.0 on pci0 isa0: <ISA bus> on isab0 vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xb400-0xb4ff mem 0xfbb00000-0xfbb000ff irq 23 at device 18.0 on pci0 miibus0: <MII bus> on vr0 rlphy0: <RTL8201L 10/100 media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr0: Ethernet address: 00:15:f2:17:7f:ac acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 2002576039 Hz quality 800 Timecounters tick every 1.000 msec ad0: DMA limited to UDMA33, device found non-ATA66 cable ad0: 39205MB <Maxtor 6K040L0 NAR61HA0> at ata0-master UDMA33 acd0: CDROM <GCR-8525B/1.02> at ata0-slave PIO4 ad2: 190782MB <Seagate ST3200826A 3.03> at ata1-master UDMA100 ad3: 286168MB <Seagate ST3300831A 3.03> at ata1-slave UDMA100 Trying to mount root from ufs:/dev/ad0s1a __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"