Today I purchased a Belkin 5 port USB PCI card, which claims to be
OHCI compliant, and backwards-compatible to USB 1.1 -- so it should
work with FreeBSD, right?.

I'm not sure where I'm going wrong, but the system doesn't seem to
detect the card.  I've tried scanpci, pcitweak, and pciconf to see if
the card shows up there (I'm not sure if those utilities actually scan
the PCI bus, or just report what's been scanned before, but...) and
still, it's not there.  I've included dmesg.boot below for those
interested.

Any hints?

TIA.

-Chris

dmesg.boot:

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.7-STABLE #0: Sat Dec 28 20:37:58 EST 2002
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/FRANKENSTEIN
Timecounter "i8254"  frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (501.14-MHz 586-class CPU)
  Origin = "AuthenticAMD"  Id = 0x58c  Stepping = 12
  Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
  AMD Features=0x80000800<SYSCALL,3DNow!>
real memory  = 402636800 (393200K bytes)
config> q
avail memory = 387244032 (378168K bytes)
Preloaded elf kernel "kernel" at 0xc0426000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc042609c.
Preloaded elf module "linux.ko" at 0xc04260ec.
K6-family MTRR support enabled (2 registers)
md0: Malloc disk
Using $PIR table, 5 entries at 0xc00f0d00
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <AcerLabs M1541 (Aladdin-V) PCI host bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <AcerLabs M5243 PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GB graphics accelerator> at 0.0
chip1: <AcerLabs M15x3 Power Management Unit> at device 3.0 on pci0
isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
rl0: <RealTek 8139 10/100BaseTX> port 0xb800-0xb8ff mem 0xde800000-0xde8000ff irq 7 at 
device 10.0 on pci0
rl0: Ethernet address: 00:e0:7d:93:ec:cc
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl1: <RealTek 8139 10/100BaseTX> port 0xb400-0xb4ff mem 0xde000000-0xde0000ff irq 9 at 
device 11.0 on pci0
rl1: Ethernet address: 00:e0:7d:94:1d:37
miibus1: <MII bus> on rl1
rlphy1: <RealTek internal media interface> on miibus1
rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
atapci0: <AcerLabs Aladdin ATA33 controller> port 0xb000-0xb00f irq 0 at device 15.0 
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/7 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pcm0: <OPTi931> at port 0x534-0x537,0x380-0x38b,0x220-0x22f,0xe0c-0xe0f irq 5 drq 0,1 
on isa0
AD_WAIT_INIT FAILED 1002000 0xff
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, 
default to deny, logging limited to 100 packets/entry by default
IPsec: Initialized Security Association Processing.
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 9787MB <WDC WD102AA> [19885/16/63] at ata0-master UDMA33
ad2: 1221MB <Seagate Technology 1275MB - ST31276A> [2482/16/63] at ata1-master WDMA2
acd0: DVD-ROM <SAMSUNG DVD-ROM SD-604> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s1a

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-questions" in the body of the message

Reply via email to