I got an Archos Jukebox Studio 20 for Christmas, and want to hook it
up to my FreeBSD box.  It's uses a usb cable for data transfer, and I've
never had to use usb on FreeBSD before.  I've done some research and the
best page I could find with instructions was
http://www.stalker.org/~sean/freebsd-p2040/... but the kernel config and
supplied archos.sh script doesn't work for me.  I'm a little behind when
it comes to usb...  is that what firewire is?

  On his page it says to compile firewire, sbp, scbus, da and umass. 
I'm cvsup'ed to 4.7 stable from release and did what he said.  When I
try and 'mount -t msdos /dev/da0s1 /archos'  I get 'Device not

  Any advice would be greatly appreciated.  Could you reply to my email
address as well as the list please b/c I'm not subscribed.


Here is my dmesg:

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
FreeBSD 4.7-STABLE #2: Fri Jan  3 10:07:48 EST 2003
    [EMAIL PROTECTED]:/usr/src/sys/compile/GUTROT
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (400.91-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x652  Stepping = 2
real memory  = 402640896 (393204K bytes)
avail memory = 387649536 (378564K bytes)
Preloaded elf kernel "kernel" at 0xc03c5000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00f0d10
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G200 AGP graphics accelerator> at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq
9 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: In-System Design USB Storage Adapter, rev 1.10/1.10, addr 2
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at
device 4.3 on pci0
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xd000-0xd07f mem
0xdf800000-0xdf80007f irq 5 at device 11.0 on pci0
xl0: Ethernet address: 00:10:5a:6a:4e:74
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <3Dfx Voodoo graphics accelerator> at 12.0
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sbc0: <Creative ViBRA16X> at port 0x220-0x22f,0x300-0x301,0x388-0x38b
irq 10 drq 0,1 on isa0
pcm0: <SB16 DSP 4.16 (ViBRA16X)> on sbc0
ad0: 29311MB <Maxtor 5T030H3> [59554/16/63] at ata0-master UDMA33
ad1: 9787MB <QUANTUM FIREBALL CX10.2A> [19885/16/63] at ata0-slave
acd0: CDROM <TOSHIBA CD-ROM XM-6402B> at ata1-master PIO4
acd1: CD-RW <CRW6206A> at ata1-slave PIO4
Mounting root from ufs:/dev/ad0s1a
can't re-use a leaf (firewire_debug)!
can't re-use a leaf (fwmem_debug)!
module_register: module fwohci/firewire already exists!
linker_file_sysinit "firewire.ko" failed to register! 17
can't re-use a leaf (sbp_debug)!
module_register: module firewire/sbp already exists!

Here is my kernel config file:

# GENERIC -- Generic kernel configuration file for FreeBSD/i386
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you
# in doubt as to the purpose or necessity of a line, check first in
# $FreeBSD: src/sys/i386/conf/GENERIC,v 2002/08/31 20:28:26
obrien Exp $

machine         i386
cpu             I386_CPU
cpu             I486_CPU
cpu             I586_CPU
cpu             I686_CPU
ident           GUTROT
maxusers        0

#makeoptions    DEBUG=-g                #Build kernel with gdb(1) debug symbols

options         MATH_EMULATE            #Support for x87 emulation
options         INET                    #InterNETworking
options         INET6                   #IPv6 communications protocols
options         FFS                     #Berkeley Fast Filesystem
options         FFS_ROOT                #FFS usable as root device [keep this!]
options         SOFTUPDATES             #Enable FFS soft updates support
options         UFS_DIRHASH             #Improve performance on big directories
options         MFS                     #Memory Filesystem
options         MD_ROOT                 #MD is a potential root device
options         NFS                     #Network Filesystem
options         NFS_ROOT                #NFS usable as root device, NFS required
options         MSDOSFS                 #MSDOS Filesystem
options         CD9660                  #ISO 9660 Filesystem
options         CD9660_ROOT             #CD-ROM usable as root, CD9660 required
options         PROCFS                  #Process filesystem
options         COMPAT_43               #Compatible with BSD 4.3 [KEEP THIS!]
options         SCSI_DELAY=15000        #Delay (in ms) before probing SCSI
options         UCONSOLE                #Allow users to grab the console
options         USERCONFIG              #boot -c editor
options         VISUAL_USERCONFIG       #visual boot -c editor
options         KTRACE                  #ktrace(1) support
options         SYSVSHM                 #SYSV-style shared memory
options         SYSVMSG                 #SYSV-style message queues
options         SYSVSEM                 #SYSV-style semaphores
options         P1003_1B                #Posix P1003_1B real-time extensions
options         ICMP_BANDLIM            #Rate limit bad replies
options         KBD_INSTALL_CDEV        # install a CDEV entry in /dev
options         AHC_REG_PRETTY_PRINT    # Print register bitfields in debug
                                        # output.  Adds ~128k to driver.
options         AHD_REG_PRETTY_PRINT    # Print register bitfields in debug 

device          isa
device          eisa
device          pci

# Floppy drives
device          fdc0    at isa? port IO_FD1 irq 6 drq 2
device          fd0     at fdc0 drive 0
device          fd1     at fdc0 drive 1

# ATA and ATAPI devices
device          ata0    at isa? port IO_WD1 irq 14
device          ata1    at isa? port IO_WD2 irq 15
device          ata
device          atadisk                 # ATA disk drives
device          atapicd                 # ATAPI CDROM drives
options         ATA_STATIC_ID           #Static device numbering

# atkbdc0 controls both the keyboard and the PS/2 mouse
device          atkbdc0 at isa? port IO_KBD
device          atkbd0  at atkbdc? irq 1 flags 0x1
device          psm0    at atkbdc? irq 12

device          vga0    at isa?

# syscons is the default console driver, resembling an SCO console
device          sc0     at isa? flags 0x100

# Floating point support - do not disable.
device          npx0    at nexus? port IO_NPX irq 13

# Power management support (see LINT for more options)
device          apm0    at nexus? disable flags 0x20 # Advanced Power Management

# Serial (COM) ports
device          sio0    at isa? port IO_COM1 flags 0x10 irq 4
device          sio1    at isa? port IO_COM2 irq 3
device          sio2    at isa? disable port IO_COM3 irq 5
device          sio3    at isa? disable port IO_COM4 irq 9

# Parallel port
device          ppc0    at isa? irq 7
device          ppbus           # Parallel port bus (required)
device          lpt             # Printer

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these
device          miibus          # MII bus support
device          xl              # 3Com 3c90x (``Boomerang'', ``Cyclone'')

# Pseudo devices - the number indicates how many units to allocate.
pseudo-device   loop            # Network loopback
pseudo-device   ether           # Ethernet support
pseudo-device   pty             # Pseudo-ttys (telnet etc)
pseudo-device   md              # Memory "disks"

# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device   bpf             #Berkeley packet filter

# USB support
device          uhci            # UHCI PCI->USB interface
device          ohci            # OHCI PCI->USB interface
device          usb             # USB Bus (required)
device          ugen            # Generic

# SCSI shit
device          scbus
device          da
device          umass

device  firewire   # firewire bus code
device  sbp        # requires scbus and da

# For PnP/PCI sound cards
device          pcm

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-questions" in the body of the message

Reply via email to