On 8/21/06, Vizion <[EMAIL PROTECTED]> wrote:

> > The motherboard is a FA-K8N51GMF-9 with 3 hard drives
> > installed. 2xSata and 1xIDE.

That mobo uses an Nvidia chipset, last I checked the drivers for that
chipset weren't that great.


> > How do I get the installer select drives interface to recognize ad6?
> >

Do you have a /dev/ad6?

I have now sifted the connected to the SATA2 connector on the motherboard -- 
but it is still not recognized.. see comments below made in the posting I have 
just made to the amd64 list.
-----------

Here is the text:
_________________
There are a number of reports in dmesg I do not understand.


\***  mark start of section 
***\  marks end of section
for each query
Can anyone please tell me what action, if any, I should take for each section.
Comment start is indicated by !!**
Multi-line comments end with **!!



Thanks in advance.
david
______________________________


Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE #0: Sun May  7 04:15:57 UTC 2006
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/SMP
ACPI APIC Table: <GBT    AWRDACPI>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3200+ (2009.16-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x20ff2  Stepping = 2
  
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  Features2=0x1<SSE3>
  AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow+,3DNow>
  AMD Features2=0x1<LAHF>
real memory  = 2080309248 (1983 MB)
avail memory = 1997578240 (1905 MB)
ioapic0 <Version 1.1> irqs 0-23 on motherboard
kbd0 at kbdmux0
acpi0: <GBT AWRDACPI> on motherboard

\***
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
    ACPI-0501: *** Error: Handler for [SystemMemory] returned AE_AML_ALIGNMENT
    ACPI-1304: *** Error: Method execution failed [\\_SB_.MEM_._CRS] (Node 
0xffffff0000bdbd80), AE_AML_ALIGNMENT
    ACPI-0239: *** Error: Method execution failed [\\_SB_.MEM_._CRS] (Node 
0xffffff0000bdbd80), AE_AML_ALIGNMENT
can't fetch resources for \\_SB_.MEM_ - AE_AML_ALIGNMENT

!!** what is going on here?
***\


cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0

\***
!!** Is this a follow up from previous section? 

pci0: <memory, RAM> at device 0.0 (no driver attached)
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
pci0: <memory, RAM> at device 0.6 (no driver attached)
pci0: <memory, RAM> at device 0.7 (no driver attached)
pci0: <display, VGA> at device 5.0 (no driver attached)
pci0: <memory, RAM> at device 9.0 (no driver attached)

***\

isab0: <PCI-ISA bridge> at device 10.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
pci0: <memory, RAM> at device 10.2 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xf7008000-0xf7008fff irq 21 at 
device 11.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7004000-0xf70040ff irq 22 at 
device 11.1 on pci0
ehci0: [GIANT-LOCKED]
usb1: EHCI version 1.0
usb1: companion controller, 8 ports each: usb0
usb1: <EHCI (generic) USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
umass0: USB2.0 CardReader, rev 2.00/91.38, addr 2
atapci0: <nVidia nForce MCP51 UDMA133 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 13.0 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <nVidia nForce MCP51 SATA300 controller> port 
0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xd800-0xd80f mem 
0xf7007000-0xf7007fff irq 23 at device 14.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
atapci2: <nVidia nForce MCP51 SATA300 controller> port 
0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xc400-0xc40f mem 
0xf7006000-0xf7006fff irq 20 at device 15.0 on pci0
ata4: <ATA channel 0> on atapci2
ata5: <ATA channel 1> on atapci2
pcib1: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pci1: <ACPI PCI bus> on pcib1
fwohci0: <Texas Instruments TSB43AB23> mem 
0xf4005000-0xf40057ff,0xf4000000-0xf4003fff irq 16 at device 6.0 on pci1
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:d0:03:56:00:b2:b7:e6
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:d0:03:b2:b7:e6
fwe0: Ethernet address: 02:d0:03:b2:b7:e6
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem 0xf4004000-0xf40040ff 
irq 17 at device 7.0 on pci1
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:30:bd:b6:d9:e0
fwohci1: <VIA Fire II (VT6306)> port 0xa400-0xa47f mem 0xf4006000-0xf40067ff 
irq 18 at device 14.0 on pci1
fwohci1: OHCI version 1.0 (ROM=1)
fwohci1: No. of Isochronous channels is 4.
fwohci1: EUI64 00:00:14:85:00:ca:4a:75
fwohci1: Phy 1394a available S400, 2 ports.
fwohci1: Link S400, max_rec 2048 bytes.
firewire1: <IEEE1394(FireWire) bus> on fwohci1
fwe1: <Ethernet over FireWire> on firewire1
if_fwe1: Fake Ethernet address: 02:00:14:ca:4a:75
fwe1: Ethernet address: 02:00:14:ca:4a:75
fwe1: if_start running deferred for Giant
sbp1: <SBP-2/SCSI over FireWire> on firewire1
fwohci1: Initiate bus reset
fwohci1: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire1: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire1: bus manager 0 (me)
pci0: <multimedia> at device 16.1 (no driver attached)
pci0: <bridge> at device 20.0 (no driver attached)
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 on 
acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd1 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd3fff,0xd4000-0xd57ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 2009158157 Hz quality 800
Timecounters tick every 1.000 msec
module_register_init: MOD_LOAD (amr_linux, 0xffffffff8062a040, 0) error 6

\***
!!**
I have the following hard drives installed.

Western Digital WD2000JD in Physical location A is SATA but does not seem to be 
recognized. Is connected via SATA Bus 2 on motherboard.
ad0 is a Western Digital WD2000JB-00KFA0 08.05J08 Physical Location B is IDE 
ata-0master UDMA100. Is connected via IDE1 on motherboard.
ad4 is a Seagate ST3160827AS 3.42 recognized as ata2 -master SATA150.Is 
connected via SATA Bus 1 on motherboard.
acd0 is a CDRW <LITE-ON CD-RW SOHR-5239S/2s03> at ata0-slave UDMA33. Is 
connected via IDE1 on motherboard.
I cannot understand why the WD2000JD is not recognized.
**!!
ad0: 190781MB <WDC WD2000JB-00KFA0 08.05J08> at ata0-master UDMA100
acd0: CDRW <LITE-ON CD-RW SOHR-5239S/2S03> at ata0-slave UDMA33
ad4: 152627MB <Seagate ST3160827AS 3.42> at ata2-master SATA150
***\
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <USB2.0 CF  CardReader > Removable Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da1 at umass-sim0 bus 0 target 0 lun 1
da1: <USB2.0 CBO CardReader > Removable Direct Access SCSI-0 device 
da1: 40.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0 
(da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:1): SCSI Status: Check Condition
(da1:umass-sim0:0:0:1): NOT READY asc:3a,0
(da1:umass-sim0:0:0:1): Medium not present
(da1:umass-sim0:0:0:1): Unretryable error
Opened disk da1 -> 6
(da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0 
(da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:1): SCSI Status: Check Condition
(da1:umass-sim0:0:0:1): NOT READY asc:3a,0
(da1:umass-sim0:0:0:1): Medium not present
(da1:umass-sim0:0:0:1): Unretryable error
Opened disk da1 -> 6
(da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0 
(da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:1): SCSI Status: Check Condition
(da1:umass-sim0:0:0:1): NOT READY asc:3a,0
(da1:umass-sim0:0:0:1): Medium not present
(da1:umass-sim0:0:0:1): Unretryable error
Opened disk da1 -> 6
Trying to mount root from ufs:/dev/ad0s1a
dragon_saver: the console does not support M_VGA_CG320
module_register_init: MOD_LOAD (dragon_saver, 0xffffffffb39ab540, 0) error 19
\***
!!** What is happening here??

pid 12388 (java), uid 0: exited on signal 6 (core dumped)
pid 40561 (java), uid 0: exited on signal 6 (core dumped)
pid 40557 (java), uid 0: exited on signal 6 (core dumped)
pid 40559 (java), uid 0: exited on signal 6 (core dumped)
pid 40560 (java), uid 0: exited on signal 6 (core dumped)
pid 40556 (java), uid 0: exited on signal 6 (core dumped)
pid 40558 (java), uid 0: exited on signal 6 (core dumped)
pid 66743 (javac), uid 0: exited on signal 6 (core dumped)
pid 99229 (conftest), uid 0: exited on signal 12 (core dumped)
***\




_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to