On a Dell D400 notebook (Pentium-M 1.4GHz, Intel 855GM, ICH4M) running
FreeBSD 7.0 #0

Closing the lid switches off the display, opening the lid does not
switch the display back on. Very annoying. The machine is fully
functional otherwise (accessed via ssh).

Noticed this first on a vanilla FreeBSD-7.0 #0 install, the optimized
kernel seems to behave the same.

In sysctl I noticed after closing and opening the lid
       hw.acpi.lid_switch_state: NONE
but I have not checked the status of this sysctl before I closed the lid.

dmesg output is not of boot -v, but of regular boot

I wouldn't care if the lid doesn't have acpi features (e.g. suspend on
lid close), but I'd like the screen to switch off for additional

Hope someone can help me!

Kind regards,

Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Fri Apr  4 07:22:22 CEST 2008
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/BEASTIE70
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1400MHz (1398.82-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping = 5
real memory  = 535453696 (510 MB)
avail memory = 514461696 (490 MB)
acpi0: <DELL CPi R  > on motherboard
acpi0: [ITHREAD]
acpi0: reservation of 0, 9fc00 (3) failed
acpi0: reservation of 100000, 1fdf0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link1: BIOS IRQ 11 for 0.31.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
vgapci0: <VGA-compatible display> port 0xc000-0xc007 mem 
0xf0000000-0xf7ffffff,0xfaf80000-0xfaffffff irq 11 at device 2.0 on pci0
agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> on vgapci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
vgapci1: <VGA-compatible display> mem 
0xe8000000-0xefffffff,0xfaf00000-0xfaf7ffff at device 2.1 on pci0
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at 
device 29.0 on pci0
uhci0: [ITHREAD]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at 
device 29.1 on pci0
uhci1: [ITHREAD]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at 
device 29.2 on pci0
uhci2: [ITHREAD]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem 0xfaeffc00-0xfaefffff 
irq 11 at device 29.7 on pci0
ehci0: [ITHREAD]
usb3: EHCI versIon 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x3001> mem 
0xfcff0000-0xfcffffff irq 11 at device 0.0 on pci1
miibus0: <MII bus> on bge0
brgphy0: <BCM5705 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge0: Ethernet address: 00:0d:56:6d:9a:9b
bge0: [ITHREAD]
cbb0: <TI7510 PCI-CardBus Bridge> at device 1.0 on pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
cbb1: <TI7610 PCI-CardBus Bridge> irq 11 at device 1.1 on pci1
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [ITHREAD]
fwohci0: <1394 Open Host Controller Interface> mem 
0xfcfef800-0xfcfeffff,0xfcfe8000-0xfcfebfff irq 11 at device 1.2 on pci1
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 32:4f:c0:00:1f:54:78:10
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x1138000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
pci1: <base peripheral> at device 1.3 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xbfa0-0xbfaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <multimedia, audio> at device 31.5 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [ITHREAD]
psm0: model GlidePoint, device ID 0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 
 pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1398818076 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert enabled, rule-based forwarding disabled, 
default to deny, logging limited to 5 packets/entry by default
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 38154MB <HTS548040M9AT00 MG2OA53A> at ata0-master UDMA100
Trying to mount root from ufs:/dev/ad0s1a
bge0: link state changed to UP
hw.acpi.supported_sleep_state: S1 S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S1
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 1
hw.acpi.verbose: 0
hw.acpi.disable_on_reboot: 0
hw.acpi.handle_reboot: 0
hw.acpi.reset_video: 0
hw.acpi.cpu.cx_lowest: C1
hw.acpi.acline: 1
hw.acpi.battery.life: 100
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 1
hw.acpi.battery.info_expire: 5
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.user_override: 0
hw.acpi.thermal.tz0.temperature: 33.5C
hw.acpi.thermal.tz0.active: -1
hw.acpi.thermal.tz0.passive_cooling: 0
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: -1
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 99.0C
hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
freebsd-questions@freebsd.org mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to