Hello,

I have successfully installed 5.0 on my IBM Thinkpad i series 1400.

Anne Sipes wrote:
Hello,

I recently tried to upgrade my IBM Thinkpad 1400i to RELENG_5_0 because I wanted the 32-bit cardbus support. I cvsup'd new source and followed these instructions from UPDATING:

<make sure you have good level 0 dumps>
<maybe fix /etc/fstab> [7]
make buildworld [9]
make buildkernel KERNCONF=YOUR_KERNEL_HERE [8]
cp src/sys/${MACHINE}/conf/GENERIC.hints /boot/device.hints [2]
make installkernel KERNCONF=YOUR_KERNEL_HERE
cd src/sys/boot ; make install [6]
[1]
<reboot in single user> [3]
Here is my mistake: I typed shutdown now. I should have actually rebooted as UPDATING says...

mergemaster -p [5]
rm -rf /usr/include/g++
make installworld

Here I ran into trouble. The installworld informed me that my kernel wasn't new enough. I'm sorry I don't have the exact error.

I was unable to complete the installworld and unable to recover.
I had to remove my Linksys Combo PCMCIA model no. EC2T before I was able to successfully reboot into single user mode and complete the installworld. I can cause a Fatal trap 12 at any time by plugging that card back in:

Stopped at pccard_scan_cis+0x1b5: movzbl 0(%eax,%edx,1),%eax

I decided to do a fresh install.

I made 5.0 boot floppies.

kern.flp loaded with no problems. I inserted mfsroot.flp and it appears to load ok until:

<text that scrolls off the screen>
unknown <PNP3780> can't assign resources (irq)
unknown <PNP0400> can't assign resources (port)
unknown <PNP0501> can't assign resources (port)
unknown <PNP0700> can't assign resources (port)
Timecouters tick every 10.000 msec

Fatal trap 12: page fault while in kernel mode
fault virtual address = 0xc703a000
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc01c669f
stack pointer = 0x10:0xc6d3a9c0
frame pointer = 0x10:0xc6d3ac04
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interupt enabled, resume, IOPL=0
current process = 6 (cbb0)
trap number = 12
panic: page fault

syncing disks, buffers remaining...
done
uptime: 1s
Automatic reboot in 15 seconds

I've installed a new 4.7 release using the 4.7 kern.flp and mfsroot.flp and booted from the generic kernel. Here is my dmesg from boot -v:

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RELEASE #0: Wed Oct 9 15:08:34 GMT 2002
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 365804707 Hz, i8254 clock: 1193176 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (365.81-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10

Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 100597760 (98240K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00536000 - 0x05fe7fff, 95100928 bytes (23218 pages)
config> di sn0
config> di lnc0
config> di ie0
config> di fe0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory = 92639232 (90468K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f0280
bios32: Entry = 0xf0210 (c00f0210) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x0
pnpbios: Found PnP BIOS data at 0xc00f62d0
pnpbios: Entry = fa000:0 Rev = 1.0
pnpbios: Event flag at 4b0
Other BIOS signatures found:
ACPI: 000fe030
Preloaded elf kernel "kernel" at 0xc050f000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc050f0a8.
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=162110b9)
pcibios: No call entry point
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x10b9, dev=0x1621, revid=0x05
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e0000000, size 26
found-> vendor=0x10b9, dev=0x5247, revid=0x01
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x11c1, dev=0x0449, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 80100000, size 8
map[14]: type 1, range 32, base 00007090, size 3
map[18]: type 1, range 32, base 00007400, size 8
found-> vendor=0x10b9, dev=0x1533, revid=0x0a
class=06-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x125d, dev=0x1969, revid=0x02
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 00007800, size 6
map[14]: type 1, range 32, base 00007850, size 4
map[18]: type 1, range 32, base 00007870, size 4
map[1c]: type 1, range 32, base 00007890, size 2
map[20]: type 1, range 32, base 000078a4, size 2
found-> vendor=0x10b9, dev=0x5229, revid=0x20 subordinatebus=0 secondarybus=0
intpin=a, irq=9
found-> vendor=0x10b9, dev=0x5237, revid=0x03
class=0c-03-10, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base 82100000, size 12
pci0: <PCI bus> on pcib0
pcib1: <AcerLabs M5247 PCI-PCI(AGP Supported) bridge> at device 1.0 on pci0
found-> vendor=0x10c8, dev=0x0005, revid=0x20
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 81000000, size 24
map[14]: type 1, range 32, base 80800000, size 22
map[18]: type 1, range 32, base 80500000, size 20
pci1: <PCI bus> on pcib1
pci1: <NeoMagic MagicMedia 256AV SVGA controller> (vendor=0x10c8, dev=0x0005) at 0.0 irq 9
pci0: <unknown card> (vendor=0x11c1, dev=0x0449) at 6.0 irq 9
isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <unknown card> (vendor=0x125d, dev=0x1969) at 8.0 irq 5
atapci0: <AcerLabs Aladdin ATA33 controller> port 0x78c0-0x78cf irq 15 at device 15.0 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x78c0
ata0: mask=03 ostat0=50 ostat2=00
ata0-slave: ATAPI 00 00
ata0-master: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x78c8
ata1: mask=01 ostat0=50 ostat2=ff
ata1-master: ATAPI 14 eb
ata1: mask=01 stat0=00 stat1=00
ata1: devices=04
ata1: at 0x170 irq 15 on atapci0
chip1: <AcerLabs M15x3 Power Management Unit> at device 17.0 on pci0
pcic0: <O2micro 6832/6833 PCI-Cardbus Bridge> irq 9 at device 19.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: Warning: O2micro OZ68xx chips may not work
pcic0: PCI Configuration space:
0x00: 0x68321217 0x04100007 0x06070034 0x00822000
0x10: 0x88000000 0x020000a0 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000001
0x30: 0x00000001 0x00000001 0x00000001 0x04200109
0x40: 0x10021025 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x0800008f 0x00820bea 0x00000000 0x00000000
0xa0: 0x7e010001 0x00c04000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pcic1: <O2micro 6832/6833 PCI-Cardbus Bridge> irq 9 at device 19.1 on pci0
pcic1: PCI Memory allocated: 0x88001000
pcic1: Warning: O2micro OZ68xx chips may not work
using shared irq9.
pcic1: PCI Configuration space:
0x00: 0x68321217 0x04100007 0x06070034 0x00822000
0x10: 0x88001000 0x020000a0 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000001
0x30: 0x00000001 0x00000001 0x00000001 0x04200109
0x40: 0x10021025 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x0800008f 0x00820bea 0x00000000 0x00000000
0xa0: 0x7e010001 0x00c04000 0x00000000 0x00000000ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
pcic-: pcic0 exists, using next available unit number
pcic-: pcic1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
adv0: not probed (disabled)
bt0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 05 50 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic2 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic3: not probed (disabled)
sio0: irq maps: 0x241 0x251 0x241 0x241
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x241 0x241 0x241 0x241
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x3bc
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at port 0x3bc-0x3c3 irq 7 on isa0
ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devicesbpf: ppp0 attached
new masks: bio 68c040, tty 631212, net 671212
bpf: sl0 attached
ad0: success setting UDMA2 on Acer chip
Creating DISK ad0
pcic0: Autodetected 5.0V card
pccard: card inserted, slot 0
pcic0: reset 1 int is 90 stat is 5f
pccard: card removed, slot 0
ar: FreeBSD check1 failed
ad0: <IBM-DBCA-204860/BC3OA82F> ATA-4 disk at ata0-master
ad0: 4645MB (9514260 sectors), 10068 C, 15 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-master: success setting PIO4 on generic chip
acd0: <CRN-8241B/1.16b> CDROM drive at ata1 as master
acd0: read 4125KB/s (32015KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 9510479, size 9510417 : OK
start_init: trying /sbin/init
pcic0: reset 1 int is 90 stat is 5f
pcic0: Autodetected 5.0V card
pccard: card inserted, slot 0
pcic0: reset 2 pcic0: Event mask 0x8
int is f0 stat is 5f
pcic0: reset 3 int is f0 stat is 7f
pcic0: reset 0
splash: image decoder found: blank_saver
Linux ELF exec handler installed
ed-: ed0 exists, using next available unit number
pccard0: Assigning ed1: io 0x300-0x31f irq 9 mem 0x0-0xffffffff
pcic: I/O win 0 flags 15 300-31f
ed1: Forcing IRQ to 9
pcic: I/O win 0 flags 5 300-31f
ed1 at port 0x300-0x31f irq 9 slot 0 on pccard0
pcic: I/O win 0 flags 15 300-31f
ed1: Forcing IRQ to 9
bpf: ed1 attached
ed1: address 00:e0:98:70:15:d8, type NE2000 (16 bit)


pcic0: Event mask 0x6
BIOS Geometries:
0:024efe3f 0..590=591 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03feff00 0..1022=1023 cylinders, 0..255=256 heads, 1..0=0 sectors
0 accounted for
Device configuration finished.
bpf: faith0 attached
bpf: lo0 attached

0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard1: <PC Card 16-bit bus (classic)> on pcic1
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0x82100000-0x82100fff at device 20.0 on pci0
pcibios: No call entry point
pci_cfgintr: BIOS 0.00 doesn't support interrupt routing
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6

class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=15
map[20]: type 1, range 32, base 000078c0, size 4
found-> vendor=0x10b9, dev=0x7101, revid=0x09
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1217, dev=0x6832, revid=0x34
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=9
found-> vendor=0x1217, dev=0x6832, revid=0x34
class=06-07-00, hdrtype=0x02, mfdev=1

It is my intention to sup new 5.0 Release source and try the upgrade again. I don't really expect to succeed. I'd appreciate any help you could give me.

Thanks,
Anne
--
Anne Sipes
--
If God had not given us sticky tape, it would have been necessary to
invent it.


To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-questions" in the body of the message

Reply via email to