I recently picked up a used Sony Vaio PCG-FX390 laptop.  It had Windows XP on
it so I decided to install FreeBSD 5.1-STABLE.

Long Story short, the install went great except the PCMCIA bridge seems to be
misconfigured.  I've googled for two days trying to find the answer but have
not come up with anything that works.  If I try and insert/remove a card the
system locks up and I'm forced to hard-power the box.  If I boot with card(s)
inserted, I get "Unsupported Card type detected" although I'm using card(s)
that are supported and work under RH Linux 9 and Windows.

I even went back to GENERIC before sending this to get the box baseline.

_any_ pointers would be appreciated.


io      0x240-0x360
irq     10 11 15
memory  0xd4000  96k
debuglevel 4

dmesg output:

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE-p5 #0: Wed Sep 24 23:13:21 EDT 2003
Preloaded elf kernel "/boot/kernel/kernel" at 0xc06d4000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06d42bc.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 993660627 Hz
CPU: Intel Pentium III (993.66-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
real memory  = 401080320 (382 MB)
avail memory = 382087168 (364 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY   U0      > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fdf30
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem 
0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 9 at device 2.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
fwohci0: <Texas Instruments TSB43AA22> mem 0xf4100000-0xf4103fff,0xf4105000-0xf41057ff 
irq 9 at device 0.0 on pci1
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 08:00:46:03:00:d5:21:8d
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:46:d5:21:8d
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
cbb0: <RF5C476 PCI-CardBus Bridge> at device 2.0 on pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib1: possible interrupts:  9
pcib1: slot 2 INTA routed to irq 9 via \\_SB_.LNKC
cbb1: <RF5C476 PCI-CardBus Bridge> at device 2.1 on pci1
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib1: possible interrupts:  9
pcib1: slot 2 INTB routed to irq 9 via \\_SB_.LNKD
fxp0: <Intel 82801BA/CAM (ICH2/3) Pro/100 Ethernet> port 0x3000-0x303f mem 
0xf4104000-0xf4104fff irq 9 at device 8.0 on pci1
fxp0: Ethernet address <snip>
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 UDMA100 controller> port 0x1800-0x180f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0x1820-0x183f irq 9 at 
device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x1840-0x185f irq 9 at 
device 31.4 on pci0
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 
irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
cbb0: Unsupported card type detected
cbb1: Unsupported card type detected
ata1-slave: ATAPI identify retries exceeded
ad0: 28615MB <IC25N030ATDA04-0> [58140/16/63] at ata0-master UDMA100
acd0: CD-RW <UJDA710> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s3a
[EMAIL PROTECTED] mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to