I'm having trouble getting a LinkSys EG1032 gigabit network card to work in RELENG_4_8.

The 4.8 Hardware Notes say the card uses the nge driver.

I grepped the LINT kernel config file for anything secific to the EG1032 and didn't find anything special, so I recompiled a kernel with "device nge".

I also have "device miibus" for the Intel EtherExpress Pro (fxp) card I'm using.

When the machine boots, I see this line:
pci0: <unknown card> (vendor=0x1737, dev=0x1032) at 13.0 irq 11

Here's my entire dmesg:

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE-p13 #7: Sat Oct 4 20:46:08 EDT 2003
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/HOST1
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 1615918372 Hz
CPU: Intel(R) Pentium(R) 4 CPU 1.60GHz (1615.92-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf12 Stepping = 2
real memory = 536805376 (524224K bytes)
avail memory = 518840320 (506680K bytes)
Preloaded elf kernel "kernel" at 0xc036b000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 9 entries at 0xc00fd840
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <SIS Generic host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib2: <PCI to PCI bridge (vendor=1039 device=0001)> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
isab0: <SiS 85c503 PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <SiS 5591 ATA100 controller> port 0xf000-0xf00f at device 2.5 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
dc0: <LC82C115 PNIC II 10/100BaseTX> port 0xe000-0xe0ff mem 0xe7434000-0xe74340ff irq 11 at device 9.0 on pci0
dc0: Ethernet address: 00:a0:cc:e3:42:95
miibus0: <MII bus> on dc0
dcphy0: <Intel 21143 NWAY media interface> on miibus0
dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xe400-0xe43f mem 0xe7400000-0xe741ffff,0xe7435000-0xe7435fff irq 12 at device 10.0 on pci0
fxp0: Ethernet address 00:02:b3:4c:74:58
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib3: <PCI to PCI bridge (vendor=1044 device=a500)> at device 11.0 on pci0
pci2: <PCI bus> on pcib3
asr0: <Adaptec Caching SCSI RAID> mem 0xe4000000-0xe5ffffff irq 9 at device 11.1 on pci0
asr0: major=154
asr0: ADAPTEC 2100S FW Rev. 370F, 1 channel, 256 CCBs, Protocol I2O
pci0: <Trident model 9660 VGA-compatible display device> at 12.0 irq 5
pci0: <unknown card> (vendor=0x1737, dev=0x1032) at 13.0 irq 11
pcib1: <SiS 5591 host to AGP bridge> on motherboard
pci3: <PCI bus> on pcib1
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
Mounting root from ufs:/dev/da0s1a
da0 at asr0 bus 0 target 0 lun 0
da0: <ADAPTEC RAID-1 370F> Fixed Direct Access SCSI-2 device
da0: Tagged Queueing Enabled
da0: 17501MB (35842048 512 byte sectors: 255H 63S/T 2231C)

Does anyone know what could be causing this to not work?

Also, I know I'm running "4.8-RELEASE-p13" and I applied the new patches manually. =)


Ken Ebling

[EMAIL PROTECTED] mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to