You have to add an line to the /etc/fstab file for the second HD.
You can mount it as an msdos HD or you can use FBSD to fdisk, label,
and format it to FBSD file system.  It's up to you and how you want
to use it.

-----Original Message-----
[mailto:[EMAIL PROTECTED] Behalf Of Michael E.
Sent: Tuesday, December 02, 2003 11:38 PM
Subject: SCSI Disk not found

Hello peoples,

I was given a Compaq Proliant 800 machine...its a pentium pro
200 MHz. I got 4.9-Stable installed and everything is running

However, I noticed that is does indeed have two scsi disks,
but freebsd only finds one.

Attached is the dmesg... notice the sym0 and sym1.
Does this supposed to tell me anything?

Michael E Mercer

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
        The Regents of the University of California. All rights
FreeBSD 4.9-STABLE #0: Tue Dec  2 21:45:22 EST 2003
    [EMAIL PROTECTED]:/usr/src/sys/compile/slow_4_9
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium Pro (199.43-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x619  Stepping = 9

real memory  = 301989888 (294912K bytes)
avail memory = 288219136 (281464K bytes)
Preloaded elf kernel "kernel" at 0xc0491000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc049109c.
ccd0-3: Concatenated disk drivers
VESA: v1.2, 1024k memory, flags:0x0, mode table:0xc03f8994 (1000014)
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <IBM 82351 PCI-PCI bridge> at device 8.0 on pci0
pci1: <PCI bus> on pcib1
sym0: <875> port 0x7000-0x70ff mem
0x40100000-0x40100fff,0x40102000-0x401020ff irq 5 at device 4.0 on
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x7400-0x74ff mem
0x40101000-0x40101fff,0x40102100-0x401021ff irq 5 at device 8.0 on
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pci1: <Cirrus Logic GD5430 SVGA controller> at 9.0
tl0: <Compaq NetFlex-3/P Integrated> port 0x6000-0x600f mem
0x40000000-0x4000000f irq 9 at device 16.0 on pci0
tl0: Ethernet address: 00:80:5f:35:d8:6d
miibus0: <MII bus> on tl0
tlphy0: <ThunderLAN 10baseT media interface> on miibus0
tlphy0:  10base2/BNC, 10base5/AUI, 10baseT, 10baseT-FDX, auto
isab0: <Intel 82371SB PCI to ISA bridge> at device 20.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> port 0xf100-0xf10f at device
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0579 (System Board)> on eisa0 slot 0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xe8000-0xedfff,0xee000-0xeffff on isa0
pmtimer0 on isa0
pca0 at port 0x40 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: cannot reserve I/O port range
IPsec: Initialized Security Association Processing.
ncp_load: [210-213]
ad1: 8207MB <ST38641A> [16676/16/63] at ata0-slave WDMA2
acd0: CDROM <HITACHI CDR-7930> at ata0-master PIO3
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at sym1 bus 0 target 0 lun 0
da0: <COMPAQ ST34371W 0682> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged
da0: 4094MB (8386000 512 byte sectors: 255H 63S/T 522C)

[EMAIL PROTECTED] mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to