I am trying to configure a COMPAQ Wirless Optical Mouse to work with KDE on 
FreeBSD 5.2.1. so far I have not been very successful. This is a USB mouse.

I can get the mouse pointer to work in FreeBSD and KDE without any problem. 
However, I can not get the wheel to work anywhere.

This is the output of the 'dmesg.today' file:

[EMAIL PROTECTED] /var/log $ cat dmesg.today
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 20:45:55 GMT 2004
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a0e000.# Identifier and 
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a0e0cc.
Preloaded elf module "/boot/kernel/sn# Identifier and driver
d_ess.ko" at 0xc0a0e178.
Preloaded elf module "/boot/kernel/snd_sbc.ko" at 0xc0a0e224.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (397.33-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x651  Stepping = 1
real memory  = 402653184 (384 MB)
avail memory = 381427712 (363 MB)
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
Using $PIR table, 5 entries at 0xc00fa040
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci_cfgintr: 0:4 INTA BIOS irq 11
pci_cfgintr: 0:20 INTD BIOS irq 11
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0x44000000-0x47ffffff at 
device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci_cfgintr: 0:1 INTA routed to irq 4
pcib1: slot 0 INTA is routed to irq 4
pci1: <display, VGA> at device 0.0 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0x2400-0x24ff mem 0x41100000-0x411000ff 
irq 11 at device 4.0 on pci0
rl0: Ethernet address: 00:50:ba:40:6d:e1
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 20.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x20a0-0x20af at device 20.1 on 
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x2080-0x209f irq 11 at 
device 20.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: MOUSE SYSTEM U+P RF Mouse Receiver, rev 1.10/0.00, addr 2, iclass 3/1
ums0: 5 buttons and Z dir.
piix0: <PIIX Timecounter> port 0xee80-0xee8f at device 20.3 on pci0
Timecounter "PIIX" frequency 3579545 Hz quality 0
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio4: <U.S. Robotics 56K Voice INT> at port 0x2f8-0x2ff irq 3 on isa0
sio4: type 16550A
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
sbc0: <ESS ES1869 (Compaq OEM)> at port 0x330-0x331,0x388-0x38b,0x220-0x22f 
irq 5 drq 3,1 on isa0
pcm0: <ESS 18xx DSP> on sbc0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (port)
Timecounter "TSC" frequency 397331698 Hz quality 800
Timecounters tick every 10.000 msec
GEOM: create disk ad0 dp=0xc3b55260
ad0: 7665MB <QUANTUM Bigfoot TX8.0AT> [15574/16/63] at ata0-master UDMA33
acd0: DVDROM <COMPAQ DVD-ROM GD-2000> at ata1-master WDMA2
GEOM: create disk afd0 dp=0xc3b5446c
afd0: REMOVABLE <IOMEGA ZIP 100 ATAPI> at ata1-slave PIO0
Mounting root from ufs:/dev/ad0s1a

This is my 'rc.conf' file:

moused_flags="z 6 7"

Finally, here the the mouse section from the 'XF86Config' file:

# Identifier and driver

    Identifier  "Mouse1"
    Driver      "mouse"
    Option "Protoco"     "Auto"
    Option "Device"      "/dev/sysmouse"
    Option "Buttons"     "7"
    Option "ZAxisMapping" "6 7"

I might add that I receive an error message upon boot up that the 'moused' was 
not supplied with the correct port. I have tried every port I can think of, 
and it sill gives me an error.

I would really appreciate any help someone might be able to afford me.


Gerard Seibert
[EMAIL PROTECTED] mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to