I am running FreeBSD 5.3. I have it presently loaded on an older Compaq
5140 computer. For some unknown reason, I am having a problem getting
DMA turned on for my CDROM drive. I am also receiving an error message
regarding the 'slave'. I had FreeBSD 5.2.1 loaded previously and never
received any such warning message. In addition, the DMA was initiated at
bootup with the same entries I now have in the 'LOADER.CONF(5)' fiie. I
reformatted the HD prior to installing the new version, so I do not
believe that the problem lies there.
Here is my 'dmesg' output:
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-STABLE #0: Fri Dec 24 20:16:07 EST 2004
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/BUDMAN
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (397.33-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x651 Stepping = 1
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 402653184 (384 MB)
avail memory = 384331776 (366 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0x50000000-0x53ffffff at
device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0x2000-0x20ff mem 0x41200000-0x412000ff
irq 11 at device 4.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:50:ba:40:6d:e1
isab0: <PCI-ISA bridge> at device 20.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0x24a0-0x24af,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 20.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x2480-0x249f irq 11 at
device 20.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: MOUSE SYSTEM U+P RF Mouse Receiver, rev 1.10/0.00, addr 2, iclass 3/1
ums0: 5 buttons and Z dir.
pci0: <bridge, PCI-unknown> at device 20.3 (no driver attached)
cpu0 on motherboard
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
sbc0: <ESS ES1869 (Compaq OEM)> at port 0x330-0x331,0x388-0x38b,0x220-0x22f irq
5 drq 3,1 on isa0
sbc0: [GIANT-LOCKED]
pcm0: <ESS 18xx DSP> on sbc0
pcm0: [GIANT-LOCKED]
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (port)
sio4: <U.S. Robotics 56K Voice INT> at port 0x2f8-0x2ff irq 3 on isa0
sio4: type 16550A
Timecounter "TSC" frequency 397331943 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 7665MB <QUANTUM Bigfoot TX8.0AT/A04.0V00> [15574/16/63] at ata0-master
UDMA33
ata1-slave: FAILURE - SETFEATURES SET TRANSFER MODE status=1<ERROR>
error=4<ABORTED>
acd0: DVDROM <COMPAQ DVD-ROM GD-2000/0056> at ata1-master PIO4
afd0: REMOVABLE <IOMEGA ZIP 100 ATAPI/14.A> at ata1-slave BIOSPIO
Mounting root from ufs:/dev/ad0s1a
I am able to turn on DMA for the drive using the 'atacontrol(8)'. I have
not had success getting the DMA initiated using the /boot/loader.conf
file however. This is my 'loader.conf' file:
snd_ess_load="YES"
hw.ata.ata_dma=1
hw.ata.atapi_dma=1
hw.ata_wc=1
I have tried using parenthesis around the numbers as well, but the results are
the
same.
I am open to any suggestions.
Thanks!
Gerard E. Seibert
[EMAIL PROTECTED]
Only in America...
Tim Allen, comedian, had this to say about Martha Stewart:
"Boy, I feel safer now that she's behind bars. O. J. & Kobe are walking
around, but they take the one woman in America willing to cook, clean,
and work in the yard and haul her ass to jail."
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
