On 11/27/12 00:24, YongHyeon PYUN wrote: > On Mon, Nov 26, 2012 at 10:13:47AM -0500, Richard Kuhns wrote: >> On 11/21/12 21:08, YongHyeon PYUN wrote: >>> On Thu, Nov 22, 2012 at 10:49:21AM +0900, YongHyeon PYUN wrote: >>>> On Wed, Nov 21, 2012 at 02:59:34PM -0500, Richard Kuhns wrote: >>>>> On 11/20/12 03:52, YongHyeon PYUN wrote: >>>>>> On Fri, Nov 16, 2012 at 10:30:04AM -0500, Richard Kuhns wrote: >>>>>>> Hi all, >>>>>>> >>>>>>> Over the last month or so I've installed FreeBSD 9 (-stable) on several >>>>>>> Mac >>>>>>> Minis via the memstick image; they seem to be pretty good little boxes >>>>>>> for >>>>>>> things like offsite secondary nameservers, for example, and they're >>>>>>> easily >>>>>>> replaced in case of problems. >>>>>>> >>>>>>> However, the newest minis have slightly different hardware, and FreeBSD >>>>>>> can't >>>>>>> find the built-in NIC. pciconf -lv on the new mini shows it as >>>>>>> >>>>>>> none3@pci0:1:0:0: class=0x020000 card=0x168614e4 chip=0x168614e4 >>>>>>> rev=0x01 >>>>>> >>>>>> It seems this controller is BCM57766. >>>>>> >>>>>>> hdr=0x00 >>>>>>> vendor = 'Broadcom Corporation' >>>>>>> class = network >>>>>>> subclass = ethernet >>>>>>> >>>>>>> The previous edition mini (that works) reports >>>>>>> >>>>>>> bge0@pci0:2:0:0: class=0x020000 card=0x16b414e4 chip=0x16b414e4 >>>>>>> rev=0x10 hdr=0x00 >>>>>>> vendor = 'Broadcom Corporation' >>>>>>> device = 'NetXtreme BCM57765 Gigabit Ethernet PCIe' >>>>>>> class = network >>>>>>> subclass = ethernet >>>>>>> >>>>>>> Is there a chance that adding the new card/chip info to the current >>>>>>> driver would >>>>>>> allow it to work? I'll be happy to test and report back. I'm afraid I'm >>>>>>> not >>>>>>> familiar enough with hardware at that level to figure out the patch >>>>>>> myself. >>>>>>> >>>>>> >>>>>> Try attached patch and let me know whether the patch works or not. >>>>>> If the patch works please share dmesg output(bge(4) and brgphy(4) >>>>>> output only). >>>>>> Note, the patch was generated against CURRENT. >>>>>> >>>>> >>>>> I'm afraid it didn't help. I ended up grabbing if_bge.c and if_bgereg.h >>>>> from >>>> >>>> I guess you also need to copy brgphy.c from HEAD to >>>> /usr/src/sys/dev/mii directory. >>>> >>>>> HEAD using svnweb.freebsd.org. The patch installed cleanly and there were >>>>> no >>>>> errors during the build, but still no NIC. >>>> >>>> Does it mean you're not seeing bge0 interface? Or you can't pass >>>> any traffic via bge0? >>> >>> Oops, it seems I've not included your device ID in the diff. >>> Try attach one instead. Make sure you use brgphy.c from HEAD. >>> >> >> There's progress! With your latest patch using brgphy.c, if_bge.c, and >> if_bgereg.h from head I'm now seeing the bge0 interface. Unfortunately, the >> moment I try to configure it the box locks up completely; it won't even >> toggle >> the caps lock LED. >> >> Booting single user and running ifconfig shows: >> >> bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 >> options=8009b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,LINKSTATE> >> ether a8:20:66:11:3b:d6 >> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> >> media: Ethernet autoselect (1000baseT <full-duplex>) >> status: active >> >> I did a verbose boot; here's the part that seems to be relevant to bge0: >> >> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x57766001> >> mem >> 0xa0400000-0xa040ffff,0xa0410000-0xa041ffff irq 16 at device 0.0 on pci1 >> bge0: CHIP ID 0x10110142; ASIC REV 0x10110; CHIP REV 0x101101; PCI-E > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > > All these information are garbage which indicates a bug in the diff. > >> miibus0: <MII bus> on bge0 >> brgphy0: <BCM57765 1000BASE-T media interface> PHY 1 on miibus0 >> brgphy0: OUI 0x001be9, model 0x0024, rev. 1 >> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow >> bge0: bpf attached >> bge0: Ethernet address: a8:20:66:11:3b:d6 >> ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 61 >> >> I greatly appreciate your efforts. I'm sorry for the delay getting back with >> you, but we had a busy Thanksgiving weekend. >> > > Try again with attached bge.57766.diff3. > Thanks for testing! >
I don't think the patch actually got attached :-( -- Richard Kuhns <[email protected]> My Desk: 765-269-8541 Wintek Corporation Internet Support: 765-269-8503 427 N 6th Street Consulting: 765-269-8504 Lafayette, IN 47901-2211 Accounting: 765-269-8502 _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[email protected]"
