Oh, that means you don't have SGPIO after all. If you do, you'll see entries like this:
<WDC WD5000BEVT-00ZAT0 01.01A01> at scbus0 target 0 lun 0 (pass0,ada0) <WDC WD30EZRX-00DC0B0 80.00A80> at scbus1 target 0 lun 0 (pass1,ada1) <WDC WD30EFRX-68N32N0 82.00A82> at scbus2 target 0 lun 0 (pass2,ada2) <AHCI SGPIO Enclosure 2.00 0001> at scbus6 target 0 lun 0 (ses0,pass3) On Fri, Jan 29, 2021 at 1:34 PM Slawa Olhovchenkov <s...@zxy.spb.ru> wrote: > On Fri, Jan 29, 2021 at 10:12:03AM -0700, Alan Somers wrote: > > > What does "camcontrol devlist" show? > > Only 2 disk: usb-flash and da1 (isci connected) > (I am currently just boot from 12.2 install) > > > On Fri, Jan 29, 2021 at 10:06 AM Slawa Olhovchenkov <s...@zxy.spb.ru> > wrote: > > > > > On Fri, Jan 29, 2021 at 09:51:33AM -0700, Alan Somers wrote: > > > > > > > I've never used any tool with SGPIO. The hardware simply isn't > powerful > > > > enough to be useful. sesutil works, in theory, to control the > LEDs. But > > > > it's of limited usefulness since there's no way to tell which drives > are > > > > installed in which slots. > > > > > > For me sesutil failed w/ "No SES device found" > > > > > > > > > > > On Fri, Jan 29, 2021 at 9:44 AM Slawa Olhovchenkov <s...@zxy.spb.ru> > > > wrote: > > > > > > > > > On Fri, Jan 29, 2021 at 09:22:47AM -0700, Alan Somers wrote: > > > > > > > > > > > The short story is: SGPIO sucks. It doesn't detect drive > presence, > > > much > > > > > > less provide physical path information. The only thing you can > do > > > with > > > > > it > > > > > > is control the fault LEDs. But doing that usefully requires you > to > > > have > > > > > > some extra source of information about what drives are installed > in > > > what > > > > > > slots. Basically, you need to track that kind of information > > > offline. > > > > > > sesutil ought to be able to control the LEDs, at least, but I've > > > never > > > > > > personally used it with SGPIO. > > > > > > > > > > What tool you used with SGPIO? > > > > > What additional drivers need? > > > > > > > > > > > On Fri, Jan 29, 2021 at 9:02 AM Slawa Olhovchenkov < > s...@zxy.spb.ru> > > > > > wrote: > > > > > > > > > > > > > I am have Supermicro MB X9DBU-iF connected to bcakplane > > > BPN-SAS-825TQ > > > > > > > by T-SGPIO cables. sesutil don't found any SES device. > > > > > > > > > > > > > > Is this posible to have control to this backplane? > > > > > > > _______________________________________________ > > > > > > > freebsd-stable@freebsd.org mailing list > > > > > > > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > > > > > > > To unsubscribe, send any mail to " > > > > > freebsd-stable-unsubscr...@freebsd.org" > > > > > > > > > > > > > _______________________________________________ > > > > > > freebsd-stable@freebsd.org mailing list > > > > > > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > > > > > > To unsubscribe, send any mail to " > > > freebsd-stable-unsubscr...@freebsd.org > > > > > " > > > > > > > > > _______________________________________________ > > > > freebsd-stable@freebsd.org mailing list > > > > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > > > > To unsubscribe, send any mail to " > freebsd-stable-unsubscr...@freebsd.org > > > " > > > > > _______________________________________________ > > freebsd-stable@freebsd.org mailing list > > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > > To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org > " > _______________________________________________ freebsd-stable@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
