Howdy,
I'm having problems with my machine locating it's second hard drive.
I've got the first hard drive and IDE ZIP drive on my first IDE channel (master
and slave, respectively) and a CD-ROM as the master on my second IDE channel.
I've got the second hard drive as the master on the Highpoint ATA66 controller,
but every time I try to mount it with "mount /data", mount whines about "Device
not configured". About two month ago I started having problems with the drive,
but didn't have a chance to look into it until now. I'm running 4.2-STABLE as
of November 22nd.
From my dmesg output (attached below), it looks like there should be four
ata devices, but only ata1-3 are being attached to my controllers and the
first HPT366 is being skipped over.
Here's the fstab which used to work:
# Device Mountpoint FStype Options Dump Pass#
/dev/ad0s1b none swap sw 0 0
/dev/ad0s1a / ufs rw 1 1
/dev/ad0s1f /usr ufs rw 2 2
/dev/ad0s1e /var ufs rw 2 2
proc /proc procfs rw 0 0
/dev/acd0c /cdrom cd9660 ro,noauto 0 0
/dev/afd0c /zip ufs rw,noauto 0 0
/dev/ad4s1e /data ufs rw 2 2
It looks like the ata code might not be quite right yet...
Thanks,
Quincey
[EMAIL PROTECTED]
> Copyright (c) 1992-2000 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 4.2-STABLE #0: Wed Nov 22 10:04:05 CST 2000
> [EMAIL PROTECTED]:/usr/obj/usr/src/sys/CLEARWATER
> Timecounter "i8254" frequency 1193182 Hz
> CPU: Pentium II/Pentium II Xeon/Celeron (467.73-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x665 Stepping = 5
>
>Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
> real memory = 201326592 (196608K bytes)
> avail memory = 193097728 (188572K bytes)
> Programming 24 pins in IOAPIC #0
> IOAPIC #0 intpin 2 -> irq 0
> FreeBSD/SMP: Multiprocessor motherboard
> cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
> cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
> io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
> Preloaded elf kernel "kernel" at 0xc02d0000.
> VESA: v3.0, 16384k memory, flags:0x1, mode table:0xc027f222 (1000022)
> VESA: NVidia
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 10
> Timecounter "PIIX" frequency 3579545 Hz
> chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at device 7.3
>on pci0
> pci0: <NVidia Riva TNT graphics accelerator> at 9.0 irq 19
> atapci1: <HighPoint HPT366 ATA66 controller> port
>0xdc00-0xdcff,0xd800-0xd803,0xd400-0xd407 irq 18 at device 19.0 on pci0
> atapci2: <HighPoint HPT366 ATA66 controller> port
>0xe800-0xe8ff,0xe400-0xe403,0xe000-0xe007 irq 18 at device 19.1 on pci0
> ata3: at 0xe000 on atapci2
> ep0: <3Com 3C509-TPC EtherLink III> at port 0x300-0x30f irq 10 on isa0
> ep0: Ethernet address 00:60:97:57:48:79
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model VersaPad, device ID 0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> APIC_IO: Testing 8254 interrupt delivery
> APIC_IO: routing 8254 via IOAPIC #0 intpin 2
> SMP: AP CPU #1 Launched!
> ad0: 3337MB <FUJITSU MPA3035ATU> [6780/16/63] at ata0-master UDMA33
> afd0: 96MB <IOMEGA ZIP 100 ATAPI> [32/64/96] at ata0-slave using PIO0
> acd0: CDROM <TOSHIBA CD-ROM XM-6102B> at ata1-master using PIO3
> Mounting root from ufs:/dev/ad0s1a
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-stable" in the body of the message
