Bios Geometrics:
0 \
1 |
2 | disk info.. snipped away bcoz it's a bit to write down to paper.
3 /
0 accounted for
Device configuration finished
bpf: lo0 attached
bpf: sl0 attached
Waiting 15 seconds for scsi devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delieverd. 0 SCBs aborted.
On Sat, 21 Sep 2002 18:47:02 +0200 - Arnvid Karstad <[EMAIL PROTECTED]> wrote:
> When booting with boot -v -s as someone nicely suggested.. this is the
> last line:
>
> (noperiph:ahc0:0:-1:-1): SCSI bus reset delieverd. 0 SCBs aborted.
>
>
> On Sat, 21 Sep 2002 18:26:57 +0200 - Arnvid Karstad <[EMAIL PROTECTED]> wrote:
>
> > Hiya,
> >
> >
> > Trying to install FreeBSD on one of the older dual cpu pentium pro
> > machines we have and it always seem to freeze up around when it's
> > supposed to wait 15 seconds for the scsi devices to settle.
> >
> > Tried to boot both 4.5 and 4.6.2 release cd's boot no luck. Linux boots
> > and shows the scsi subsystem being:
> >
> > SCSI subsystem driver Revision: 1.00
> > scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13
> > <Adaptec aic7880 Ultra SCSI adapter>
> > aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
> >
> > Vendor: COMPAQPC Model: DORS-32160 Rev: WA8B
> > Type: Direct-Access ANSI SCSI revision: 02
> > (scsi0:A:0): 20.000MB/s transfers (20.000MHz, offset 15)
> > Vendor: QUANTUM Model: FIREBALL SE8.4S Rev: PJ0A
> > Type: Direct-Access ANSI SCSI revision: 02
> > (scsi0:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
> > Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X
> > Type: Direct-Access ANSI SCSI revision: 02
> > (scsi0:A:2): 20.000MB/s transfers (20.000MHz, offset 15)
> > Vendor: IBM Model: CDRM00203 !K Rev: 8B08
> > Type: CD-ROM ANSI SCSI revision: 02
> > (scsi0:A:6): 10.000MB/s transfers (10.000MHz, offset 15)
> > scsi0:0:0:0: Tagged Queuing enabled. Depth 253
> > scsi0:0:1:0: Tagged Queuing enabled. Depth 253
> > scsi0:0:2:0: Tagged Queuing enabled. Depth 253
> > Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> > Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
> > Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
> > SCSI device sda: 4110000 512-byte hdwr sectors (2104 MB)
> > Partition check:
> > sda: sda1
> > SCSI device sdb: 16777215 512-byte hdwr sectors (8590 MB)
> > sdb: sdb1 sdb2 sdb3
> > SCSI device sdc: 6281856 512-byte hdwr sectors (3216 MB)
> > sdc: sdc1 sdc2 sdc3
> > Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
> >
> >
> > Anyone got any good ideas?
> >
> >
> > Mvh/Best regards,
> >
> > Arnvid L. Karstad
> >
> >
> >
> > To Unsubscribe: send mail to [EMAIL PROTECTED]
> > with "unsubscribe freebsd-stable" in the body of the message
>
>
> Mvh/Best regards,
>
> Arnvid L. Karstad
>
>
Mvh/Best regards,
Arnvid L. Karstad
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-stable" in the body of the message
