Thanks for quick answer.
I think I am sure, because if I connect this hard drive from this
onboard Promise controller with same cable to onboard VIA8237 it works
well. I tried other HDD - 76319MB <ST380817AS/3.42> [155061/16/63] at
ata5-master SATA150 not with same cable, I had exactly the same problem.
FreeBSD box.freebsd 5.4-RELEASE-p6 FreeBSD 5.4-RELEASE-p6 #0: Wed Aug 31
00:09:53 CEST 2005 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/18BOX i386
My BOX has Soltek SL-K890PRO-939 with onboard integrated this Promise RAID
Dmesg in attachement.
Now I am looking for this in dmesg: atapci0: failed: rid 0x20 is memory,
requested 4
atapci0: <Promise PDC20579 SATA150 controller> port
0xc000-0xc0ff,0xdf00-0xdf7f mem
0xdc0c0000-0xdc0dffff,0xdc0e6000-0xdc0e6fff irq 19 at device 7.0 on pci0
atapci0: failed: rid 0x20 is memory, requested 4
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
ata4: channel #2 on atapci0
Tomas Randa
pete wright wrote:
On 9/12/05, *Tomas Randa* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
Hello,
I have very strange problem with my FreeBSD box and Promise PDC20579
SATA controller:
[EMAIL PROTECTED]:7:0: class=0x010400 card=0x3574105a chip=0x3574105a
rev=0x02 hdr=0x00
vendor = 'Promise Technology Inc'
device = 'Promise SATAII150 579 (tm) IDE Controller'
class = mass storage
subclass = RAID
ad4: 381554MB <ST3400832AS/3.02> [775221/16/63] at ata2-master SATA150
Problem is, that every HDD connected to this controller is corrupting
data. For example: I copy good tar.gz archive to this drive, and
if I do
decompression immediately after copying, there is no problem, but if I
wait for example 10 minutes, then decompression ends with CRC error:
box# gzip -d ./2005-09-11.tar.gz
gzip: ./2005-09-11.tar.gz: invalid compressed data--crc error
gzip: ./2005-09-11.tar.gz: invalid compressed data--length error
I know, that problem is not in HDD or CPU/RAM, but in controller.
Could
it be a driver problem or not? I tried to turn off soft-updates, but
with no change. I have no any ideas what to do or what to try.
Thanks a lot for any answer or opinion.
Are you sure that it is not an issue with the drives? Just to make
sure, you have attached these drives to another, known working system
and seen the same issues. Also, have you made sure that the cabling
to the drives themselves are not broken, and are seated properlly. To
be sure, I'd grab a set of working sata cables and test out again.
Finally, if you have done this hardware trouble shooting already and
are sure that it is not a hardware issue with your
disks/cabling/controller itself I would post the version of FreeBSD
you are running (uname -ar) along with a dmesg to the list.
-p
--
~~o0OO0o~~
Pete Wright
www.nycbug.org <http://www.nycbug.org>
NYC's *BSD User Group
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE-p6 #0: Wed Aug 31 00:09:53 CEST 2005
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/18SHINZON
module_register: module pci/em already exists!
Module pci/em failed to register: 17
ACPI APIC Table: <K8T890 AWRDACPI>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3500+ (2199.76-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x20ff0 Stepping = 0
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500000<NX,AMIE,LM,DSP,3DNow!>
real memory = 3220045824 (3070 MB)
avail memory = 3153993728 (3007 MB)
ioapic0 <Version 0.3> irqs 0-23 on motherboard
ioapic1 <Version 0.3> irqs 24-47 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <K8T890 AWRDACPI> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral, interrupt controller> at device 0.5 (no driver attached)
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 27 at device 2.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 35 at device 3.1 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> irq 39 at device 3.2 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> irq 43 at device 3.3 on pci0
pci6: <ACPI PCI bus> on pcib6
atapci0: <Promise PDC20579 SATA150 controller> port 0xc000-0xc0ff,0xdf00-0xdf7f
mem 0xdc0c0000-0xdc0dffff,0xdc0e6000-0xdc0e6fff irq 19 at device 7.0 on pci0
atapci0: failed: rid 0x20 is memory, requested 4
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
ata4: channel #2 on atapci0
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port
0xd800-0xd83f mem 0xdc0a0000-0xdc0bffff,0xdc080000-0xdc09ffff irq 16 at device
8.0 on pci0
em0: Ethernet address: 00:07:e9:01:61:fc
em0: Speed:N/A Duplex:N/A
ahd0: <Adaptec 29320 Ultra320 SCSI adapter> port 0xc800-0xc8ff,0xc400-0xc4ff
mem 0xdc0e2000-0xdc0e3fff irq 17 at device 9.0 on pci0
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
ahd1: <Adaptec 29320 Ultra320 SCSI adapter> port 0xd000-0xd0ff,0xcc00-0xccff
mem 0xdc0e0000-0xdc0e1fff irq 18 at device 9.1 on pci0
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
pci0: <serial bus, FireWire> at device 12.0 (no driver attached)
atapci1: <VIA 6420 SATA150 controller> port
0xde00-0xde0f,0xdd00-0xdd03,0xdc00-0xdc07,0xdb00-0xdb03,0xda00-0xda07 irq 20 at
device 15.0 on pci0
ata5: channel #0 on atapci1
ata6: channel #1 on atapci1
atapci2: <VIA 8237 UDMA133 controller> port
0xe000-0xe00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
ata0: channel #0 on atapci2
ata1: channel #1 on atapci2
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
acpi_tz0: <Thermal Zone> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
orm0: <ISA Option ROM> at iomem 0xcd000-0xce7ff on isa0
pmtimer0 on isa0
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounter "TSC" frequency 2199763800 Hz quality 800
Timecounters tick every 10.000 msec
ipfw2 initialized, divert disabled, rule-based forwarding disabled, default to
deny, logging limited to 100 packets/entry by default
ad4: 381554MB <ST3400832AS/3.02> [775221/16/63] at ata2-master SATA150
ad10: 76319MB <ST380817AS/3.42> [155061/16/63] at ata5-master SATA150
ad12: 76318MB <ST380817AS/3.42> [155058/16/63] at ata6-master SATA150
Waiting 15 seconds for SCSI devices to settle
da0 at ahd1 bus 0 target 0 lun 0
da0: <SEAGATE ST336754LW 0004> Fixed Direct Access SCSI-3 device
da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C)
Mounting root from ufs:/dev/ad10s1a
em0: Link is up 100 Mbps Full Duplex
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
